Skip to content

← Electricity and Magnetism

Potential, Potential Difference and Potential Energy

Unit 21 · CDC textbook pages 403–415

Hide the stories, facts, photos, activities and interactives, for revising before an exam
In this unit 8 sections
  1. 21.1 Electrical potential
  2. 21.2 The potential due to a point charge
  3. 21.3 Relation between E and V
  4. 21.4 Potential difference and the electron volt
  5. 21.5 Potential gradients
  6. 21.6 Graphical interpretations of electric field strength and potential
  7. 21.7 Similarities between electric and gravitational fields
  8. Exercise

A bird sits on a bare power line carrying 11,000 volts and preens its feathers, quite unharmed. You walk across a carpet on a dry winter day, reach for a door handle, and a spark a few thousand volts strong snaps at your finger. Twelve volts from a car battery can’t be felt at all, yet the same twelve volts can start an engine. What is a volt, then, and why does the number alone tell you so little about danger?

The answer is electric potential: the energy a charge has per coulomb because of where it is in an electric field. In Unit 19 you met electric charges and Coulomb’s law, and in Unit 20 the electric field, the force per unit charge. This unit does for electricity what the gravitational potential did for gravity in Unit 7: it replaces forces, which are vectors and hard to add, with energies per unit charge, which are plain numbers. You will find the potential of a point charge, see how the field and the potential are two descriptions of the same thing, draw maps of equal potential, and use the electron volt, the energy unit of atoms. The capacitors of Unit 22 rest on all of it.

21.1 Electrical potential

The electric potential V V at a point is the work done in bringing a unit positive test charge from infinity to that point (without accelerating it, so that all the work is stored). If bringing a charge Q Q there takes work W W ,

V=work done in bringing the charge from infinitycharge=WQ V = \frac{\text{work done in bringing the charge from infinity}}{\text{charge}} = \frac{W}{Q}

Its SI unit is the joule per coulomb (J/C), called the volt (V): a point is at 1 V when it takes 1 J of work to bring 1 C there from infinity. Potential is a scalar: it has a size and a sign, but no direction.

Because the work done is stored as potential energy, there is a second way to say the same thing: the potential at a point is the electric potential energy per unit charge that a charge placed there would have. A charge Q Q at a point of potential V V has potential energy QV QV .

The definition follows the gravitational potential exactly (Unit 7’s 7.6 Gravitational potential, the work per kilogram to bring a mass from infinity), and “infinity” means the same thing: a place so far away that the force is zero there, where we take the potential to be zero. The difference is that gravity only attracts, while charges can attract or repel, so the electric potential can be negative or positive.

Opposite charges attract, and the situation is exactly as in gravitation. A negative charge near a positive one is held by the attraction: to pull it away to infinity you must do work. So, near a positive charge, a negative charge has less energy than it would have far away: its potential energy is negative, and it climbs to zero as the charges are separated.

Like charges repel. Imagine two negative charges held some distance apart. Bringing them together from infinity took work, against the push, and that work was stored in the pair. Let them go and they fly apart: the stored energy turns into their kinetic energy, until they are so far apart that the push is zero. Their potential energy was positive: it rose above zero as they were pushed together, and falls back to zero as they fly apart.

−1−0.50.510102030energy (mJ)distance between them, r (cm)like charges: +unlike charges: −
Figure 21.1 The energy stored by two charges of 50 nC against the distance between them. For like charges (positive energy) it falls as they fly apart; for unlike charges (negative energy) it rises towards zero as they are pulled apart. Either way, zero is “far apart”.

A charge of +2.0 μC is brought from infinity to a point P. The work done on it is 8.0 × 10⁻⁴ J. The potential at P is:

Pick an answer to see why.

21.2 The potential due to a point charge

Let us find the potential at a distance r r from a single point charge Q Q , in free space (air is nearly the same).

++A, charge +QB, charge +Q′Fmoved Δxx
Figure 21.2 A point charge +Q at A and a second charge +Q′ at B, a distance x away. A pushes B away with a force F. An outside agent moves B a small step Δx towards A, against F.

Derivation: V=14πε0Qr V = \dfrac{1}{4\pi\varepsilon_0}\dfrac{Q}{r}

Measure distances x x from A, where the charge Q Q is (Figure 21.2).

  1. By Coulomb’s law, the charge Q Q at A pushes the charge Q′ Q' at B away with a force

F=14πε0 QQ′x2 F = \frac{1}{4\pi\varepsilon_0}\,\frac{QQ'}{x^2}

  1. An outside agent moves the charge at B a small distance Δx \Delta x towards A. The step is so small that F F hardly changes over it. The agent pushes against F F , so it does work. As B moves towards A, x x gets smaller: Δx \Delta x is a negative number, and the work done by the agent is

ΔW=−F Δx=−14πε0 QQ′x2 Δx \Delta W = -F\,\Delta x = -\frac{1}{4\pi\varepsilon_0}\,\frac{QQ'}{x^2}\,\Delta x

The minus sign makes ΔW \Delta W positive, because the motion is opposite to F F .

  1. Add up the work from infinity (x=∞ x = \infty ) to a distance r r from A (x=r x = r ). In the limit of very small steps the sum is an integral:

W=−QQ′4πε0∫∞rdxx2=−QQ′4πε0[−1x]∞r=−QQ′4πε0(−1r+0)=QQ′4πε0 r W = -\frac{QQ'}{4\pi\varepsilon_0}\int_\infty^r \frac{dx}{x^2} = -\frac{QQ'}{4\pi\varepsilon_0}\left[-\frac{1}{x}\right]_\infty^r = -\frac{QQ'}{4\pi\varepsilon_0}\left(-\frac{1}{r} + 0\right) = \frac{QQ'}{4\pi\varepsilon_0\,r}

  1. If Q′ Q' is a unit positive charge, this work is, by definition, the potential at that distance:

V=14πε0 Qr=kQrk=14πε0=8.99×109 N m2/C2 \boxed{V = \frac{1}{4\pi\varepsilon_0}\,\frac{Q}{r} = \frac{kQ}{r}} \qquad k = \frac{1}{4\pi\varepsilon_0} = 8.99\times10^9 \text{ N m}^2/\text{C}^2

Compare Unit 7’s derivation of V=−GM/r V = -GM/r : the same steps, the same integral. Gravity’s minus sign is there because gravity attracts; here, with Q Q positive, the force repels and the work done is positive.

A charge of 1.0 nC gives, at 10 cm, a potential of V=8.99×109×1.0×10−90.10=90 V = \dfrac{8.99\times10^9 \times 1.0\times10^{-9}}{0.10} = 90 V.

Four things the formula tells you

  1. Potential is a scalar, so the potential at a point due to several point charges is the algebraic sum of the potentials due to each, signs included. There are no angles and no components to work out: this is why potentials are so much easier to handle than fields.
  2. The sign follows the charge: the potential due to a positive charge is positive, and that due to a negative charge is negative.
  3. All points at the same distance from a point charge are at the same potential. They lie on a sphere round the charge. A surface over which the potential is the same everywhere is called an equipotential surface, and at every point of one the electric field is perpendicular to the surface (21.5).
  4. The potential energy of a charge Q′ Q' at a distance r r from a point charge Q Q is the work done to bring it there:

Ep=14πε0 QQ′r E_p = \frac{1}{4\pi\varepsilon_0}\,\frac{QQ'}{r}

positive for like charges, negative for unlike ones, as in 21.1.

A charge of +4 nC and a charge of −4 nC are 30 cm apart. At the point halfway between them:

Pick an answer to see why.

21.3 Relation between E and V

field E+A, +QB (higher V)FΔx
Figure 21.3 A small charge +Q at A in an electric field E, which points to the left. An outside force F moves it to the right, against the field, a short distance Δx to B, which is at a higher potential.

Suppose a force F F moves a charge +Q +Q from a point A in an electric field E E to a nearby point B, a short distance Δx \Delta x along the x-axis (Figure 21.3). The distance is so small that the field, and the force, are the same all the way from A to B.

  1. The work done by the force is

ΔW=F Δx \Delta W = F\,\Delta x

  1. The field pushes the charge with a force EQ EQ . To move the charge against the field without accelerating it, the outside force must be equal and opposite to that push:

F=−EQ F = -EQ

(the minus sign: we are working out the work done by an outside agent against the field). So

ΔW=−EQ Δx \Delta W = -EQ\,\Delta x

  1. If the potential difference between A and B is ΔV \Delta V (B being at the higher potential), the work done in carrying Q Q from A to B is, by the definition of potential,

ΔW=Q ΔV \Delta W = Q\,\Delta V

  1. The two are the same work: −EQ Δx=Q ΔV -EQ\,\Delta x = Q\,\Delta V , so

E=−ΔVΔx \boxed{E = -\frac{\Delta V}{\Delta x}}

The ratio ΔVΔx \dfrac{\Delta V}{\Delta x} is the rate at which the potential changes with distance at a point in the field: it is called the potential gradient there. So the electric field strength is the negative of the potential gradient. The minus sign says that the field points the way the potential falls: if V increases in the positive direction of x, as it does going from A to B, the field points in the negative direction of x, from B to A. A positive charge, left alone, moves “downhill” in potential, the way a ball rolls downhill.

This also explains why the field strength has two units. From E=−ΔV/Δx E = -\Delta V/\Delta x , its unit is the volt per meter, V/m. And
1 Vm=1 J/Cm=1 N mC m=1 NC 1\ \frac{\text{V}}{\text{m}} = 1\ \frac{\text{J/C}}{\text{m}} = 1\ \frac{\text{N m}}{\text{C m}} = 1\ \frac{\text{N}}{\text{C}}
so V/m and N/C are the same unit, as Unit 20 claimed.

Along a line, the potential rises from 20 V to 50 V over 0.15 m, at a steady rate. The electric field along the line is:

Pick an answer to see why.

The potential along that line, worked out point by point, shows both zeros, and the field as the slope:

Try it

The potential along a line

Drag the yellow probe along the line through the two charges (or use the slider). The red line is the tangent to the curve: the field along the line is minus its slope. Find the two places where V = 0, and see that the field there isn’t zero.

+−OA−3000−1500150030000015304560V (volts)x (cm)
Scale:
From +3 at O
+2,997 V
From −2 at A
−2,997 V
Potential V
0 V
E = −slope
83 kV/m →

Here the potential is zero: the two charges’ shares in the readouts are equal and opposite, and cancel. The field is not zero, though: the curve still slopes. Zero potential doesn’t mean zero field.

21.4 Potential difference and the electron volt

In a circuit, and in most experiments, what matters is not the potential at one point but the difference between two. The potential difference between two points A and B is the work done in carrying a unit positive charge from A to B:

ΔV=VB−VA=WA→BQ \Delta V = V_B - V_A = \frac{W_{A\to B}}{Q}

measured in volts. A potential difference of 1 V between two points means that 1 J of work is done in carrying 1 C from one to the other. The battery that is “9 V” keeps its + terminal 9 V above its − terminal: every coulomb that goes round a circuit from + to − can give 9 J to the circuit.

When a charge q q goes from A to B:

  • the work done by an outside agent (if it moves without speeding up) is W=q ΔV W = q\,\Delta V ;
  • its potential energy changes by ΔEp=q ΔV \Delta E_p = q\,\Delta V ;
  • the work done by the field is the opposite, −q ΔV -q\,\Delta V . If the charge is free, that work becomes kinetic energy: ΔEk=−q ΔV \Delta E_k = -q\,\Delta V .

Signs matter. A positive charge going to a higher potential (ΔV>0 \Delta V > 0 ) gains potential energy, so it must be pushed. An electron, q=−e q = -e , going to a higher potential loses potential energy, so the field speeds it up: electrons fall “uphill” in potential.

The electron volt

Atoms, electrons and nuclei deal in energies so small that the joule is clumsy. Physicists use the energy an electron gains in falling through 1 V:

1 electron volt=1 eV=e×1 V=1.60×10−19 J \textbf{1 electron volt} = 1\ \text{eV} = e \times 1\ \text{V} = 1.60\times10^{-19}\ \text{J}

The electron volt is a unit of energy, not of potential: it is the kinetic energy a particle with charge e e (an electron or a proton) gains when it is accelerated through a potential difference of 1 V. A charge e e accelerated through V V volts gains V V eV. Its multiples are the keV (10³ eV), MeV (10⁶ eV), GeV (10⁹ eV) and TeV (10¹² eV).

Something About
a photon of visible light 2 to 3 eV
to pull the electron out of a hydrogen atom 13.6 eV
an electron in an old television’s picture tube 25 keV
the electrons in a dental X-ray machine 60 to 70 keV
the energy given out when one uranium nucleus splits 200 MeV
a proton in the Large Hadron Collider, near Geneva (since 2022) 6.8 TeV

The electron gun

In an electron gun a filament, heated red hot, gives off electrons, which a positive anode pulls across a vacuum. An electron starting at rest and accelerated through a potential difference V V gains kinetic energy eV eV :

12mv2=eV⇒v=2eVm \frac{1}{2}mv^2 = eV \qquad\Rightarrow\qquad v = \sqrt{\frac{2eV}{m}}

So the final speed grows as the square root of the voltage: four times the voltage gives twice the speed (Exercise 10). Picture tubes, X-ray tubes and electron microscopes all begin this way.

Two views of the glass neck of an old television picture tube with the electron gun inside: a row of metal cylinders on glass supports, wired to the pins of the base at the right
Figure 21.5 The electron gun of a black-and-white television picture tube made in 1980, seen from two sides. The heated cathode sits in the small cylinder nearest the pins, on the right; the cylinders to its left are held at rising positive potentials, which speed the electrons up and focus them into a beam heading left, towards the screen. Photo: Mister rf, CC BY-SA 4.0

Try it

Accelerate an electron

Set the voltage between the filament and the anode, or choose one from the exercise. Press × 4 voltage and watch the speed: it only doubles.

filament, 0 Vanode, +0.10 V00.511.52speed (m/s)8.4 × 10⁵0V (volts)
Kinetic energy
0.10 eV
In joules
1.60 × 10⁻²⁰ J
Speed
1.87 × 10⁵ m/s

Through 0.10 V the field gives the electron 0.10 eV of kinetic energy, 1.60 × 10⁻²⁰ J. Since ½mv² = eV, v = √(2eV/m) = 1.87 × 10⁵ m/s, which is 0.062% of the speed of light.

A proton (charge +e) and an alpha particle (charge +2e) are each accelerated from rest through 500 V. Their kinetic energies are:

Pick an answer to see why.

21.5 Potential gradients

An electric field can be pictured by its field lines (Unit 20), or by its equipotentials: lines, or in three dimensions surfaces, joining points at the same potential. An equipotential surface is one on which all points are at the same potential. The potential difference between any two points on it is zero, so no work is needed to move a charge from one point on it to another.

A test charge moving along an equipotential has constant potential energy. That can only be so if the field does no work on it, which means the force from the field is at right angles to its motion. So the field lines cross every equipotential surface at right angles, along its normal. The equipotentials of an electric field are like those of a gravitational field (Unit 7): both are lines of constant potential energy for a test object, a test charge in one case and a test mass in the other.

++150 V+200 V+300 V+600 V
Figure 21.6 A single positive charge (here +2.0 nC). Field lines (red) go straight out; the equipotentials (blue) are circles, here 3, 6, 9 and 12 cm from it, at 600, 300, 200 and 150 V. Each 3 cm step outwards lowers the potential by less, as the field weakens.
+−−200 V−100 V0 V+100 V+200 V
Figure 21.7 Equal and opposite charges (+1.0 nC and −1.0 nC, 12 cm apart). The equipotentials surround each charge, positive round one and negative round the other; the 0 V equipotential is the straight line halfway between them. Every field line crosses every equipotential at a right angle.
+++180 V+250 V+400 V
Figure 21.8 Two equal positive charges (+1.0 nC each, 12 cm apart). Close in, each charge has its own equipotentials (400 V); farther out, at 250 V and 180 V, one equipotential surrounds both.

The potential gradient at a point in an electric field is the change of potential per unit change of distance in a given direction, ΔV/Δx \Delta V/\Delta x .

  1. If the field is non-uniform, as round the charges above, the potential gradient changes from place to place and with direction. The closer the equipotentials are, the greater the potential gradient at right angles to them, and so the stronger the field.
  2. If the field is uniform, as between two oppositely charged parallel plates, the equipotentials between the plates are equally spaced lines parallel to the plates (Figure 21.9).
− plate, 0 V+ plate, +VV/4V/23V/4equipotentialsdashedV0dpotentialdistance x from the − plate
Figure 21.9 Top: parallel plates a distance d apart, the negative plate at 0 V and the positive plate at +V. The field lines (red) are straight and parallel, from + to −; the equipotentials (dashed) at V/4, V/2 and 3V/4 are equally spaced. Bottom: the potential against the distance x from the negative plate, a straight line from 0 to V.

The graph shows that the potential, measured from the negative plate, is proportional to the distance x x from it: the potential gradient is the same everywhere between the plates. The potential increases in the opposite direction to the field, and its gradient is Vd \dfrac{V}{d} . The electric field strength between the plates is also Vd \dfrac{V}{d} , directed from the + plate to the − plate. In other words, the electric field strength is the negative of the potential gradient:

E=Vd(uniform field, from + to −) E = \frac{V}{d} \quad \text{(uniform field, from + to −)}

The statement still holds when the field is not uniform, but then the gradient has to be taken over a short distance: ΔV/Δx \Delta V/\Delta x , where ΔV \Delta V is the change of potential between two points a small distance Δx \Delta x apart, instead of V/d V/d . Because the potential gradient points opposite to the field lines, in general

electric field strength E=−ΔVΔx \boxed{\text{electric field strength } E = -\frac{\Delta V}{\Delta x}}

Two parallel plates 2.0 cm apart are connected to a 240 V supply. A point P is 0.50 cm from the negative plate. The potential at P (taking the negative plate as 0 V) and the field at P are:

Pick an answer to see why.

Dozens of small birds perched along the wires of an overhead power line, dark against an orange evening sky
Figure 21.10 Birds on a power line. Both of a bird’s feet are on the same wire, at the same potential, so there is no potential difference across its body and no current through it. A large bird that touches two wires at once, or a wire and an earthed pole, can be killed. Photo: Vanja Kovac, CC BY-SA 4.0
A smiling young woman with one hand on the metal dome of a Van de Graaff generator, her long hair standing out from her head in every direction
Figure 21.11 A woman touching a Van de Graaff generator at the American Museum of Science and Energy, Oak Ridge, USA. Kept insulated from the ground, her whole body is charged to the dome’s potential, which can be hundreds of thousands of volts, yet she feels nothing: her body is one equipotential, so no current flows through it. Her hairs, all charged alike, push each other apart. Touching an earthed object would be another matter. Photo: doe-oakridge . 82-25 DOE photo by Frank Hoffman, Public domain

21.6 Graphical interpretations of electric field strength and potential

0 V2 V4 V6 V8 V10 V12 V+6.0 cm between the plates
Figure 21.12 (a) Plates 6.0 cm apart at 0 V and 12 V. The equipotentials, every 2 V, are equally spaced; the field points from the 12 V plate to the 0 V plate, and pushes a positive charge between them towards the 0 V plate.

Figure 21.12 is a reminder of the field between charged parallel plates: the equipotentials are equally spaced. Figure 21.13 (b) is a graph of measurements of the potential at points between the plates, plotted against the distance from the 0 V plate. It is a straight line, because the field is uniform. A graph of the field strength against the distance from the 0 V plate, Figure 21.13 (c), is a straight line parallel to the distance axis.

048120123456potential (V)distance from the 0 V plate (cm)0−100−200−300E (N/C)E = −200 N/C everywhere(same distance axis as above)
Figure 21.13 (b) The potential measured at points between the plates against distance from the 0 V plate: the crosses lie on a straight line from 0 V to 12 V. (c) The field strength against distance: −200 N/C everywhere between the plates.

The gradient of the potential–distance graph is change in Vchange in x \dfrac{\text{change in } V}{\text{change in } x} , and since the graph is a straight line, it is Vd=12 V0.060 m=200 \dfrac{V}{d} = \dfrac{12\ \text{V}}{0.060\ \text{m}} = 200 V/m, the size of E. This leads to

electric field strength E=−potential gradient=−ΔVΔx \text{electric field strength } E = -\text{potential gradient} = -\frac{\Delta V}{\Delta x}

(Δ \Delta , as usual, stands for “change in”.)

What the minus sign means. Here x x is measured from the 0 V plate towards the 12 V plate, the direction in which the potential rises. The field points the other way, from 12 V back to 0 V, in the negative direction of x x . So E=−12 V0.060 m=−200 E = -\dfrac{12\ \text{V}}{0.060\ \text{m}} = -200 V/m: a field of 200 V/m pointing towards smaller x x . That is why graph (c) is drawn at −200 N/C. The rule always works the same way:

  • going against the field (upstream) takes you to a higher potential: ΔV \Delta V is positive;
  • going with the field (downstream) takes you to a lower potential: ΔV \Delta V is negative.

In Figure 21.12 the field pushes the positive charge to the left. Moving left from the 12 V plate to the 0 V plate, ΔV=0−12=−12 \Delta V = 0 - 12 = -12 V and Δx=−0.060 \Delta x = -0.060 m, so E=−ΔVΔx=−−12−0.060=−200 E = -\dfrac{\Delta V}{\Delta x} = -\dfrac{-12}{-0.060} = -200 V/m, the same answer: whichever way you go, the formula gives the field in the direction of +x +x , and the minus sign of the result says it points the other way.

An electron between the plates. If an electron moves from the 0 V plate towards the 12 V plate, a position of higher potential, its potential energy is reduced: ΔEp=q ΔV=(−e)(+12 V)=−12 \Delta E_p = q\,\Delta V = (-e)(+12\ \text{V}) = -12 eV, because the electron’s charge is negative and ΔV \Delta V is positive. If it is free to move it accelerates in this direction, gaining 12 eV of kinetic energy from the field at the expense of its electric potential energy.

An electron is released from rest at the 0 V plate of Figure 21.12. When it reaches the 12 V plate, it has:

Pick an answer to see why.

Areas under the graphs

A graph of force against distance for a constant force is a flat line, Figure 21.14 (a). The work done when this force moves an object a distance Δr \Delta r is the area under the graph, F×Δr=W F \times \Delta r = W . When the force varies with distance, as an electric force usually does, the work done is still the area under the graph, Figure 21.14 (b) (Unit 5, the graphical method).

Electric field strength is force per unit charge, so the area under a graph of electric field strength against distance is the work done per unit charge: the change in potential.

FrworkΔr(a)FrworkΔr(b)ErAB, on to ∞ →r₁r₂rE = kQ/r²(c)
Figure 21.14
  • a.A constant force: the work is the rectangle F × Δr.
  • b.A varying force: the work is the area under the curve.
  • c.The field of a positive point charge, E = kQ/r²: area A, between r₁ and r₂, is the potential difference between those two points; area B, from r all the way out to infinity, is the potential at r.

Figure 21.14 (c) shows how the field of a single positive point charge varies with distance: an inverse-square curve. Area A is the potential change between r1 r_1 and r2 r_2 . Area B is the potential at r r , because it is the change of potential between infinity, where the potential is zero, and r r ; the area goes on all the way out to infinity, but it is finite, since the curve falls so fast.

Derivation: V=kQ/r V = kQ/r from the field

  1. From E=−ΔVΔr E = -\dfrac{\Delta V}{\Delta r} , in the limit of a very small step, E=−dVdr E = -\dfrac{dV}{dr} , so a small step dr dr changes the potential by

dV=−E dr dV = -E\,dr

  1. For a point charge, E=14πε0Qr2=kQr2 E = \dfrac{1}{4\pi\varepsilon_0}\dfrac{Q}{r^2} = \dfrac{kQ}{r^2} .
  2. Add up the changes from infinity, where V∞=0 V_\infty = 0 , to a distance r r from the charge:

∫∞rdV=Vr−V∞=Vr=∫∞r−E dr=−kQ∫∞rdrr2=−kQ[−1r]∞r=kQr \int_\infty^r dV = V_r - V_\infty = V_r = \int_\infty^r -E\,dr = -kQ\int_\infty^r \frac{dr}{r^2} = -kQ\left[-\frac{1}{r}\right]_\infty^r = \frac{kQ}{r}

V=kQr=14πε0 Qr \boxed{V = \frac{kQ}{r} = \frac{1}{4\pi\varepsilon_0}\,\frac{Q}{r}}

This is the same expression as in 21.2, reached from the field instead of from the force. It says that the closer we are to a positive charge, the greater (more positive) the potential; the closer we are to a negative charge, the more negative the potential.

Vr0(a) Q positiveV = kQ/rVr0(b) Q negativeV = −k|Q|/r
Figure 21.15 The potential against the distance r from a single point charge Q when the charge is (a) positive and (b) negative. Both approach zero far away.

Since the potential is the work done in moving a unit positive charge from infinity to a point, the work needed to move a charge q q from infinity to that point is V×q V \times q . This is the potential energy that the charge q q has because of its position in the field. If the field comes from a single point charge Q Q :

Ep=qV=kqQr=14πε0 qQr E_p = qV = \frac{kqQ}{r} = \frac{1}{4\pi\varepsilon_0}\,\frac{qQ}{r}

Graphs of the field strength and the potential against distance for a single positive point charge show the two descriptions side by side (Figure 21.16): the potential is the area under the field’s curve, and the field is minus the slope of the potential’s curve.

ErE = kQ/r²area EΔr = −ΔVVr00V = kQ/rslope ΔV/Δr = −E
Figure 21.16 For a positive point charge: top, the field strength E = kQ/r² against r, with a thin strip of area EΔr, the fall in potential over Δr; bottom, the potential V = kQ/r against r, with a tangent whose slope is −E. The field falls off faster (1/r²) than the potential (1/r).

The potential at a distance r from a point charge is 120 V and the field there is 600 V/m. The distance r is:

Pick an answer to see why.

21.7 Similarities between electric and gravitational fields

Newton’s law of gravitation and Coulomb’s law have the same shape, so the two forces behave alike in many ways. There are also important differences.

The main similarities:

  1. Both are non-contact forces: they act across a distance, without anything touching.
  2. Both have infinite range.
  3. Both obey inverse-square laws.

The main differences:

  1. Gravitational forces between masses are always attractive; electric forces can be attractive or repulsive.
  2. An electric force is much stronger than the gravitational force: between two protons, about 10³⁶ times stronger.
  3. An electric force can be shielded (a metal box keeps it out); nothing shields gravity.
  4. An electric force acts only on charged objects; the gravitational force acts on all objects.
Characteristic Gravitation Electric
Acts on mass (positive only) charge (positive or negative)
Force (N) F=GMmr2 F = \dfrac{GMm}{r^2} , attractive only, infinite range F=14πε0Qqr2 F = \dfrac{1}{4\pi\varepsilon_0}\dfrac{Qq}{r^2} , attractive or repulsive, infinite range
Relative strength 1 10³⁶
Field strength g=Fm g = \dfrac{F}{m} E=FQ E = \dfrac{F}{Q}
Units N/kg N/C or V/m
Radial field g=GMr2 g = \dfrac{GM}{r^2} E=14πε0Qr2=kQr2 E = \dfrac{1}{4\pi\varepsilon_0}\dfrac{Q}{r^2} = \dfrac{kQ}{r^2}
Potential difference ΔV=ΔWm \Delta V = \dfrac{\Delta W}{m} ΔV=ΔWQ \Delta V = \dfrac{\Delta W}{Q}
Units J/kg J/C (volt)
Potential gradient g=−ΔVΔr g = -\dfrac{\Delta V}{\Delta r} E=−ΔVΔr E = -\dfrac{\Delta V}{\Delta r}
Potential in radial fields V=−GMr V = -\dfrac{GM}{r} , V=0 V = 0 at ∞ V=Q4πε0r V = \dfrac{Q}{4\pi\varepsilon_0 r} , V=0 V = 0 at ∞
Potential energy Ep=−GMmr E_p = -\dfrac{GMm}{r} Ep=Qq4πε0r E_p = \dfrac{Qq}{4\pi\varepsilon_0 r}

The 10³⁶ comes from comparing the two forces between two protons, ke2Gmp2=8.99×109×(1.60×10−19)26.67×10−11×(1.67×10−27)2≈1.2×1036 \dfrac{ke^2}{Gm_p^2} = \dfrac{8.99\times10^9 \times (1.60\times10^{-19})^2}{6.67\times10^{-11} \times (1.67\times10^{-27})^2} \approx 1.2\times10^{36} , the same at any distance, since both forces fall as 1/r2 1/r^2 . Why, then, does gravity rule the Moon and the planets? Because big bodies have almost exactly as much positive as negative charge, and their electric forces cancel, while every kilogram adds to gravity. Why Is Gravity So Weak? tells that story.

Which of these is true of gravitational fields but not of electric fields?

Pick an answer to see why.

Exercise

Choose the correct option

  1. The electric field between two charged plates is known to be 650 N/C. If the distance between the plates is 12 cm, what is the potential difference between the plates?

Pick an answer to see why.

Figure 21.17 For question 2: four straight, parallel, equally spaced field lines, all pointing the same way.
  1. The field in the figure:

Pick an answer to see why.

Answer these questions

3.

Explain why the test charges we use when measuring electric fields must be small.

Hint
Answer
4.

When determining an electric field, must we use a positive test charge, or would a negative one do as well? Explain.

Hint
Answer
5.

Why can electric field lines never cross?

Hint
Answer
6.

Given two point charges, Q and 2Q, a distance ℓ apart, is there a point along the straight line that passes through them where the electric field is zero when their signs are (a) opposite, (b) the same? If yes, state roughly where this point will be.

Hint
Answer
7.

If two points are at the same potential, does this mean that no net work is done in moving a test charge from one point to the other? Does this imply that no force is exerted? Explain.

Hint
Answer
8.

If a negative charge is initially at rest in an electric field, will it move toward a region of higher potential or lower potential? What about a positive charge? How does the potential energy of the charge change in each instance? Explain.

Hint
Answer
9.

State clearly the difference (a) between electric potential and electric field, (b) between electric potential and electric potential energy.

Hint
Answer
10.

An electron is accelerated from rest by a potential difference of 0.10 V. How much greater would its final speed be if it is accelerated with four times as much voltage? Explain.

Hint
Answer
11.

Is there a point along the line joining two equal positive charges where the electric field is zero? Where the electric potential is zero? Explain.

Hint
Answer
12.

Can a particle ever move from a region of low electric potential to one of high potential and yet have its electric potential energy decrease? Explain.

Hint
Answer
13.

If V = 0 at a point in space, must E = 0 there? If E = 0 at some point, must V = 0 at that point? Explain. Give examples for each.

Hint
Answer
14.

Is the electric potential energy of two isolated unlike charges positive or negative? What about two like charges? What is the significance of the sign of the potential energy in each case?

Hint
Answer

Choose the correct option, with a reason

  1. A +0.2 μC charge is in an electric field. What happens if that charge is replaced by a +0.4 μC charge?

Pick an answer to see why.

  1. Which of the following statements is valid?

Pick an answer to see why.

  1. Two identical positive charges are placed near each other. At the point halfway between the two charges,

Pick an answer to see why.

  1. A proton and an electron are in a constant electric field created by oppositely charged plates. You release the proton from near the positive plate and the electron from near the negative plate. Which feels the larger electric force?

Pick an answer to see why.

Numerical problems

19.

How much work does the electric field do in moving a −7.7 μC charge from ground to a point whose potential is 65 V higher?

Hint
Answer
20.

How strong is the electric field between two parallel plates 6.8 mm apart if the potential difference between them is 220 V?

Hint
Answer
21.

What potential difference is needed to stop an electron that has an initial velocity of 6.0 × 10⁵ m/s? (me=9.11×10−31 m_e = 9.11\times10^{-31} kg)

Hint
Answer
22.

A point charge Q creates an electric potential of +165 V at a distance of 15 cm. What is Q?

Hint
Answer
23.

In the Bohr model of the hydrogen atom, an electron orbits a proton (the nucleus) in a circular orbit of radius 0.53 × 10⁻¹⁰ m. (a) What is the electric potential at the electron’s orbit due to the proton? (b) What is the kinetic energy of the electron? (c) What is the total energy of the electron in its orbit? (d) What is the ionization energy, that is, the energy required to remove the electron from the atom and take it to infinity, at rest?

Hint
Answer
24.

How much voltage must be used to accelerate a proton (radius 1.2 × 10⁻¹⁵ m) so that it has sufficient energy to just “touch” a silicon nucleus? A silicon nucleus has a charge of +14e and its radius is about 3.6 × 10⁻¹⁵ m. Assume the potential is that for point charges.

Hint
Answer
25.

An electron is liberated from a hot filament, and attracted by an anode, of potential 1200 volts positive with respect to the filament. What is the speed of the electron when it strikes the anode? (me=9.1×10−31 m_e = 9.1\times10^{-31} kg)

Hint
Answer
26.

A 9.0 V battery is connected across two large parallel plates that are separated by 4.5 mm of air, creating a potential difference of 9.0 V between the plates. (a) What is the electric field in the region between the plates? (b) An electron is released from rest at the negative plate. If the only force on the electron is the electric force exerted by the electric field of the plates, what is the speed of the electron as it reaches the positive plate? The mass of an electron is me=9.11×10−31 m_e = 9.11\times10^{-31} kg.

Hint
Answer

A companion to your textbook, not a replacement for it: study from the book your school uses, and where the two differ, follow your teacher. Found a mistake? Please tell us.