Skip to content

← Grade 12 Physics

Exam practice

Every question from the end of every unit, with hints and answers to open. After you check an answer, mark how you did, and come back to the ones you didn’t get.

11 questions

Unit 19 · Alternating Current

Answer these questions

11.

An alternating current I varies with time t as shown in the graph above. Use the graph to answer:

  • a.What is the peak value of the current?
  • b.What is the current at t = 0.23 s?
  • c.Find the period and frequency of the current.
  • d.Find the rms value and the mean value (over half a cycle) of the current.
Hint

Read the period between two crossings of zero in the same direction. For b, use I=I0sin⁡(2πt/T) I = I_0 \sin(2\pi t/T) , since the current starts at zero and rises.

Answer
  • a.The highest point of the curve: I₀ = 17 A.
  • b.The current starts at zero and rises, so I=17sin⁡(2πt0.1) I = 17 \sin\left(\dfrac{2\pi t}{0.1}\right) . At t = 0.23 s, 2π×0.230.1=4.6π \dfrac{2\pi \times 0.23}{0.1} = 4.6\pi , which is the same angle as 0.6π = 108°:

I=17sin⁡108∘=17×0.951=16.2 A I = 17 \sin 108^\circ = 17 \times 0.951 = 16.2 \text{ A}
(On the graph, 0.23 s is just after the peak at 0.225 s.)

  • c.The current rises through zero at t = 0, 0.10 s, 0.20 s and 0.30 s, so the period T = 0.10 s and the frequency f = 1/T = 10 Hz.
  • d.Irms=I02=171.414= I_{\text{rms}} = \dfrac{I_0}{\sqrt{2}} = \dfrac{17}{1.414} = 12.0 A. Mean over half a cycle: Im=2I0π=0.637×17= I_m = \dfrac{2I_0}{\pi} = 0.637 \times 17 = 10.8 A (over a whole cycle the mean is zero).
12.
  • a.What is the power factor of a purely capacitive circuit?
  • b.Obtain an expression for the phase relationship between the current and the voltage in a purely capacitive circuit.
  • c.Why is a purely capacitive circuit an open circuit for d.c.?
  • d.An iron-cored coil of 2 H and 50 Ω resistance is placed in series with a resistor of 450 Ω, and a 200 V, 50 Hz a.c. supply is connected across them. Find the current in the coil, its phase angle relative to the supply voltage, and the p.d. across the coil.
Hint

d. The phase angle uses the whole resistance, 450 + 50 Ω.

Answer
  • a.In a pure capacitor the current leads the voltage by 90°, so the power factor is cos⁡90∘= \cos 90^\circ = 0: no power is used.
  • b.Let I=I0sin⁡ωt I = I_0 \sin \omega t . The charge is q=∫I dt=−I0ωcos⁡ωt q = \int I\,dt = -\dfrac{I_0}{\omega}\cos \omega t , so the p.d. is

V=qC=−I0ωCcos⁡ωt=−V0cos⁡ωt=V0sin⁡(ωt−π2) V = \frac{q}{C} = -\frac{I_0}{\omega C}\cos \omega t = -V_0\cos \omega t = V_0 \sin\left(\omega t - \frac{\pi}{2}\right)
with V0=I0XC V_0 = I_0X_C , XC=1ωC X_C = \dfrac{1}{\omega C} . The voltage lags the current by π/2 (90°); the current leads (Section 19.7).

  • c.For d.c., f = 0, so XC=12πfC X_C = \dfrac{1}{2\pi fC} is infinite. Physically, the plates are separated by an insulator: once the capacitor has charged to the supply’s p.d., no more charge flows, so no steady current passes. It acts as a break in the circuit, an open circuit.
  • d.As Example 19.14: XL=628.3 Ω X_L = 628.3\ \Omega , Z=5002+628.32=803 Ω Z = \sqrt{500^2 + 628.3^2} = 803\ \Omega , I = 200/803 = 0.25 A; tan⁡ϕ=628.3/500=1.257 \tan \phi = 628.3/500 = 1.257 , φ = 51.5° (the current lags the supply voltage); the coil’s impedance 502+628.32=630.3 Ω \sqrt{50^2 + 628.3^2} = 630.3\ \Omega , so the p.d. across the coil = 0.249 × 630.3 = 157 V.
13.

a. Define the rms value of a.c.
The graph above shows how the sinusoidal current I in a resistor of 450 Ω varies with time t. Use it to find, for the time from t = 0 to t = 30 ms:

  • b.the frequency of the current;
  • c.the mean current;
  • d.the rms current;
  • e.the energy dissipated in the resistor.
Hint

Read the peak and the period from the graph. How many whole cycles fit into 30 ms? Energy = Irms2Rt I_{\text{rms}}^2Rt .

Answer
  • a.The rms value of an alternating current is the steady (d.c.) current that, passing through the same resistance for the same time, produces the same amount of heat as the alternating current. For a sine wave, Irms=I0/2 I_{\text{rms}} = I_0/\sqrt{2} .
  • b.The peaks come at about 2.5 ms and 17.5 ms, so the period T = 15 ms, and f=10.015= f = \dfrac{1}{0.015} = 66.7 Hz.
  • c.0 to 30 ms is exactly two whole cycles, in which the current is positive and negative equally: the mean current is zero. (The mean over a half cycle, the “mean value” of Section 19.3, is 2I0/π=0.637×0.75=0.48 2I_0/\pi = 0.637 \times 0.75 = 0.48 A.)
  • d.The peak is 0.75 A, so Irms=0.752= I_{\text{rms}} = \dfrac{0.75}{\sqrt{2}} = 0.53 A.
  • e.E=Irms2Rt=0.532×450×0.030= E = I_{\text{rms}}^2Rt = 0.53^2 \times 450 \times 0.030 = 3.8 J.
14.
  • a.What is the power factor of a purely inductive circuit?
  • b.Obtain an expression for the phase relationship between the current and the voltage in a purely inductive circuit.
  • c.Why is a purely inductive circuit a short circuit for d.c.?
  • d.A coil with inductance and resistance is connected to an oscillator giving a fixed sinusoidal output of 5 V rms. At 50 Hz the rms current in the coil is 1 A, and at 100 Hz it is 0.625 A. Find the inductance of the coil.
Hint

d. Write Z² = R² + 4π²f²L² at both frequencies and subtract. The result is L², not L.

Answer
  • a.In a pure inductor the voltage leads the current by 90°, so the power factor is cos⁡90∘= \cos 90^\circ = 0.
  • b.Let I=I0sin⁡ωt I = I_0 \sin \omega t . With no resistance, the source’s e.m.f. balances the back e.m.f.: V=LdIdt=ωLI0cos⁡ωt=V0sin⁡(ωt+π2) V = L\dfrac{dI}{dt} = \omega LI_0 \cos \omega t = V_0 \sin\left(\omega t + \dfrac{\pi}{2}\right) , with V0=I0XL V_0 = I_0X_L , XL=ωL X_L = \omega L . The voltage leads the current by π/2 (90°) (Section 19.6).
  • c.For d.c., f = 0, so XL=2πfL=0 X_L = 2\pi fL = 0 : a steady current induces no back e.m.f., and an ideal coil is then just a wire of zero resistance, a short circuit.
  • d.As Example 19.9: Z1=5 Ω Z_1 = 5\ \Omega , Z2=8 Ω Z_2 = 8\ \Omega ; L2=82−524π2(1002−502)=1.32×10−4 L^2 = \dfrac{8^2 - 5^2}{4\pi^2(100^2 - 50^2)} = 1.32 \times 10^{-4} H², so L = 0.0115 H = 11.5 mH.
15.

An inductor, a capacitor and a resistor are connected in series with a source of alternating voltage, as above.

  • a.Write the relationship between the current and the voltage.
  • b.Draw a phasor diagram to show the leading or lagging relation between the voltage and the current.
  • c.In the series LCR circuit, R = 25 Ω, L = 30 mH and C = 10 μF, connected to a 240 V, 50 Hz a.c. source. Calculate the current and the voltmeter reading across the capacitor.
Hint

c. Find XL X_L and XC X_C first. Which is bigger? Then Z, I, and VC=IXC V_C = IX_C .

Answer
  • a.I=VZ=VR2+(XL−XC)2 I = \dfrac{V}{Z} = \dfrac{V}{\sqrt{R^2 + (X_L - X_C)^2}} , with the e.m.f. leading the current by φ, where tan⁡ϕ=XL−XCR \tan \phi = \dfrac{X_L - X_C}{R} .
  • b.Draw I along the horizontal; VR V_R along it; VL V_L straight up and VC V_C straight down; their difference VL−VC V_L - V_C up (if XL>XC X_L > X_C ); and V the hypotenuse from the origin, at φ above I (Figure 19.14). If XC>XL X_C > X_L , VL−VC V_L - V_C points down and V is below I.
  • c.XL=2π×50×0.030=9.42 Ω X_L = 2\pi \times 50 \times 0.030 = 9.42\ \Omega ; XC=12π×50×10×10−6=318.3 Ω X_C = \dfrac{1}{2\pi \times 50 \times 10 \times 10^{-6}} = 318.3\ \Omega .

Z=252+(9.42−318.3)2=625+95 407=309.9 Ω Z = \sqrt{25^2 + (9.42 - 318.3)^2} = \sqrt{625 + 95\,407} = 309.9\ \Omega
I=240309.9=0.774 A,VC=IXC=0.774×318.3=247 V I = \frac{240}{309.9} = \textbf{0.774 A}, \qquad V_C = IX_C = 0.774 \times 318.3 = \textbf{247 V}
The voltmeter across the capacitor reads more than the 240 V supply: the coil’s p.d. (7.3 V), in the opposite direction, cancels part of it. The circuit is capacitive: the current leads by tan⁡−1(308.9/25)=85.4∘ \tan^{-1}(308.9/25) = 85.4^\circ .

16.
  • a.Write the expression for the impedance of an LCR circuit.
  • b.Find the condition for resonance in an LCR circuit.
  • c.A circuit consists of a capacitor of 2 μF and a resistor of 1000 Ω. An alternating e.m.f. of 12 V (rms), 50 Hz is applied. Find the current, the p.d. across the capacitor and the phase angle between the applied e.m.f. and the current.
Answer
  • a.Z=R2+(XL−XC)2=R2+(ωL−1ωC)2 Z = \sqrt{R^2 + (X_L - X_C)^2} = \sqrt{R^2 + \left(\omega L - \dfrac{1}{\omega C}\right)^2} .
  • b.Z is least, and the current greatest, when XL=XC X_L = X_C , that is ωL=1ωC \omega L = \dfrac{1}{\omega C} , which gives the resonant frequency f0=12πLC f_0 = \dfrac{1}{2\pi\sqrt{LC}} . Then Z = R and the current is in phase with the e.m.f.
  • c.XC=12π×50×2×10−6=1592 Ω X_C = \dfrac{1}{2\pi \times 50 \times 2 \times 10^{-6}} = 1592\ \Omega .

Z=10002+15922=1880 Ω,I=121880=6.38×10−3 A=6.4 mA Z = \sqrt{1000^2 + 1592^2} = 1880\ \Omega, \qquad I = \frac{12}{1880} = 6.38 \times 10^{-3} \text{ A} = \textbf{6.4 mA}
VC=IXC=6.38×10−3×1592=10.2 V V_C = IX_C = 6.38 \times 10^{-3} \times 1592 = \textbf{10.2 V}
tan⁡ϕ=XCR=15921000=1.59,ϕ=57.9∘ \tan \phi = \frac{X_C}{R} = \frac{1592}{1000} = 1.59, \qquad \phi = 57.9^\circ
the e.m.f. lagging behind the current. (Check: VR=6.4 V_R = 6.4 V, and 6.42+10.22=12 \sqrt{6.4^2 + 10.2^2} = 12 V.)

17.

The graph shows how the e.m.f. and the current vary with time in an LCR series circuit.

  • i.Is the phase constant φ (the angle by which the e.m.f. leads the current) positive or negative? Explain.
  • ii.Sketch a phasor diagram for this case.
  • iii.Is the circuit more inductive or more capacitive? Explain.
  • iv.To increase the rate at which energy is delivered to the resistance, should the inductance be increased or decreased? Justify your answer.
Hint

Which wave reaches its peak first, reading from left to right?

Answer
  • i.The e.m.f. reaches each peak before the current does (its peaks are to the left of the current’s), so the e.m.f. leads the current: φ is positive.
  • ii.Draw the current phasor I, and the e.m.f. phasor V, longer, an angle φ anticlockwise from it (ahead of it), with φ between 0 and 90°. (The p.d. VR V_R lies along I, and VL−VC V_L - V_C points at 90° ahead of I.) This is the diagram of Figure 19.14.
  • iii.The e.m.f. leads, so tan⁡ϕ=XL−XCR>0 \tan \phi = \dfrac{X_L - X_C}{R} > 0 : XL>XC X_L > X_C . The circuit is more inductive.
  • iv.The power is Irms2R I_{\text{rms}}^2R , largest at resonance, where XL=XC X_L = X_C . Here XL X_L is too large, so decrease L: XL X_L comes down towards XC X_C , Z falls, the current rises and more energy is delivered to R each second. (Decreasing L also moves the resonant frequency 1/(2πLC) 1/(2\pi\sqrt{LC}) up towards the supply’s frequency.)
18.
  • a.The graph in question 13 shows how the sinusoidal current in a 450 Ω resistor varies with time. Use it to find, for t = 0 to t = 30 ms: i. the frequency of the current; ii. the energy dissipated in the resistor.
  • b.Discuss the phase relationship between the voltage and the current in an a.c. circuit with a capacitor and a resistor in series, and so derive the expression for the impedance of the circuit.
  • c.An air-cored coil and an electric bulb are connected in series across a 220 V, 50 Hz a.c. supply, and the bulb glows with some brightness. How will its glow change if a capacitor is added in series?
Answer
  • a.i. T = 15 ms, so f = 1/0.015 = 66.7 Hz. ii. Irms=0.75/2=0.53 I_{\text{rms}} = 0.75/\sqrt{2} = 0.53 A; E=Irms2Rt=0.532×450×0.030= E = I_{\text{rms}}^2Rt = 0.53^2 \times 450 \times 0.030 = 3.8 J.
  • b.The same current I flows through R and C. VR=IR V_R = IR is in phase with I; VC=IXC V_C = IX_C lags I by 90°. The supply’s e.m.f. is their phasor sum, so from the right-angled triangle, V2=VR2+VC2=I2(R2+XC2) V^2 = V_R^2 + V_C^2 = I^2(R^2 + X_C^2) . The impedance is Z=VI=R2+XC2=R2+1ω2C2 Z = \dfrac{V}{I} = \sqrt{R^2 + X_C^2} = \sqrt{R^2 + \dfrac{1}{\omega^2C^2}} , and the e.m.f. lags the current by φ with tan⁡ϕ=XC/R \tan \phi = X_C/R (Section 19.9).
  • c.Adding the capacitor brings in XC X_C , which cancels part of the coil’s XL X_L . If XC<2XL X_C < 2X_L the impedance R2+(XL−XC)2 \sqrt{R^2 + (X_L - X_C)^2} becomes smaller, the current larger and the bulb brighter (brightest at resonance, XC=XL X_C = X_L ); if XC>2XL X_C > 2X_L , the bulb becomes dimmer (Test yourself 19.3).
19.
  • a.Define the impedance of an LCR circuit.
  • b.The series LCR circuit above is connected across an a.c. source of e.m.f. 50 V and 50 Hz. i. Calculate the impedance of the circuit, if L = 60 mH, C = 0.50 μF and R = 300 Ω. ii. How does resonance occur in this circuit? Write the expression needed.
  • c.A device X is connected across an a.c. source of voltage V=V0sin⁡ωt V = V_0 \sin \omega t , and the current through X is I=I0sin⁡(ωt+π2) I = I_0 \sin\left(\omega t + \dfrac{\pi}{2}\right) . i. Identify the device X, and write an expression for its reactance. ii. Draw a graph of the voltage and the current over one cycle for X.
Answer
  • a.The impedance of an LCR circuit is its total opposition to a.c., the ratio of the rms (or peak) voltage to the rms (or peak) current: Z=VI=R2+(XL−XC)2 Z = \dfrac{V}{I} = \sqrt{R^2 + (X_L - X_C)^2} , in ohms.
  • b.i. XL=2π×50×0.060=18.8 Ω X_L = 2\pi \times 50 \times 0.060 = 18.8\ \Omega ; XC=12π×50×0.50×10−6=6366 Ω X_C = \dfrac{1}{2\pi \times 50 \times 0.50 \times 10^{-6}} = 6366\ \Omega .

Z=3002+(18.8−6366)2=90 000+40 288 000=6354 Ω≈6.35 kΩ Z = \sqrt{300^2 + (18.8 - 6366)^2} = \sqrt{90\,000 + 40\,288\,000} = 6354\ \Omega \approx 6.35\ \text{k}\Omega
(The current is only 50/6354 = 7.9 mA, leading the voltage by 87°.)

  • ii.Resonance occurs when the supply’s frequency makes XL=XC X_L = X_C , at f0=12πLC=12π0.060×0.50×10−6=919 f_0 = \dfrac{1}{2\pi\sqrt{LC}} = \dfrac{1}{2\pi\sqrt{0.060 \times 0.50 \times 10^{-6}}} = 919 Hz. At 50 Hz the circuit is far from resonance; raising the source’s frequency to 919 Hz (or changing L or C so that f0=50 f_0 = 50 Hz) would bring it to resonance, with Z = 300 Ω and the current in phase with the voltage.
  • c.i. The current leads the voltage by π/2 (90°): X is a capacitor, with reactance XC=1ωC=12πfC X_C = \dfrac{1}{\omega C} = \dfrac{1}{2\pi fC} .
  • ii.Over one cycle, the voltage is a sine wave starting at zero and rising; the current is a sine wave a quarter of a cycle ahead, starting at its peak +I0 +I_0 at t = 0, falling to zero when the voltage peaks (as Figure 19.10 shows).
20.
  • a.What is wattless current?
  • b.Figures a, b and c above show three a.c. circuits with equal currents. i. If the frequency of the e.m.f. is increased, what happens to the current in each? Explain. ii. What difference do you expect in the opposition to the current in circuits a and b if the a.c. e.m.f. is replaced by an equivalent d.c. e.m.f.?
Answer
  • a.A current that flows but uses no power, because it is 90° out of phase with the e.m.f., so P=VrmsIrmscos⁡90∘=0 P = V_{\text{rms}}I_{\text{rms}}\cos 90^\circ = 0 : the current in a pure inductor or a pure capacitor.
  • b.i. a. Resistor: R does not depend on frequency, so the current stays the same. b. Inductor: XL=2πfL X_L = 2\pi fL rises with f, so the current decreases. c. Capacitor: XC=1/(2πfC) X_C = 1/(2\pi fC) falls as f rises, so the current increases.
  • ii.In a, the opposition is R for d.c. as for a.c.: no change. In b, the coil’s reactance disappears for d.c. (XL=0 X_L = 0 at f = 0), leaving only the small resistance of its wire (zero for an ideal coil): the opposition becomes much smaller, and the current much larger, dangerously so for a real circuit without a resistor.
21.
  • a.Define resonance in an a.c. circuit, with one example.
  • b.Prove that the resonant frequency of an a.c. series LCR circuit is f=12πLC f = \dfrac{1}{2\pi\sqrt{LC}} .
  • c.The maximum capacitance of a variable capacitor is 33 pF. What self-inductance must be connected to it for the natural frequency of the LC circuit to be 810 kHz, a frequency in Radio Nepal’s medium-wave (AM) band?
Answer
  • a.Electrical resonance happens in a series LCR circuit when the frequency of the applied e.m.f. equals the circuit’s natural frequency: the inductive and capacitive reactances are equal and cancel, the impedance is least (Z = R), and the current is greatest and in phase with the e.m.f. Example: tuning a radio, whose LC circuit is set to resonate at the chosen station’s frequency (Activity 19.2).
  • b.Z=R2+(ωL−1ωC)2 Z = \sqrt{R^2 + \left(\omega L - \dfrac{1}{\omega C}\right)^2} is least when the bracket is zero: ωL=1ωC \omega L = \dfrac{1}{\omega C} , so ω2=1LC \omega^2 = \dfrac{1}{LC} , ω=1LC \omega = \dfrac{1}{\sqrt{LC}} . With ω=2πf \omega = 2\pi f , f=12πLC f = \dfrac{1}{2\pi\sqrt{LC}} (Section 19.11).
  • c.L=14π2f2C=14π2×(810×103)2×33×10−12=1.17×10−3 L = \dfrac{1}{4\pi^2f^2C} = \dfrac{1}{4\pi^2 \times (810 \times 10^3)^2 \times 33 \times 10^{-12}} = 1.17 \times 10^{-3} H = 1.17 mH.