Skip to content

← Grade 12 Physics

Exam practice

Every question from the end of every unit, with hints and answers to open. After you check an answer, mark how you did, and come back to the ones you didn’t get.

11 questions

Unit 18 · Electromagnetic Induction

Answer the following

11.
  • a.State Faraday’s laws of electromagnetic induction.
  • b.A coil has 5000 turns. What e.m.f. is induced in it when the magnetic flux through it changes by 8 × 10⁻⁴ Wb in 0.1 s?
  • c.A light aluminium ring hangs from a long thread, with a bar magnet near it along its axis. When the magnet is moved away from the ring, the ring follows the magnet. Why? What would happen if the magnet were moved towards the ring?
Answer
  • a.First law: whenever the magnetic flux linked with a closed circuit changes, an e.m.f. is induced in it, lasting as long as the flux keeps changing. Second law: the magnitude of the induced e.m.f. is directly proportional to the rate of change of the flux linkage: ε=−N dΦdt \varepsilon = -N\,\dfrac{d\Phi}{dt} .
  • b.Taking 8 × 10⁻⁴ Wb as the change of flux through each turn:

∣ε∣=N ΔΦt=5000×8×10−40.1=40 V |\varepsilon| = \frac{N\,\Delta\Phi}{t} = \frac{5000 \times 8 \times 10^{-4}}{0.1} = \mathbf{40\ V}
c. As the magnet moves away, the flux through the ring decreases. By Lenz’s law the induced current in the ring opposes this decrease: the face of the ring near the magnet becomes the pole opposite to the magnet’s near pole, so the ring is attracted and follows the magnet. If the magnet were moved towards the ring, the flux would increase, the ring’s near face would become a like pole, and the ring would be repelled, moving away from the magnet. Either way, the ring moves so as to reduce the relative motion.

12.

Lenz’s law gives the direction of an induced e.m.f.

  • a.State Lenz’s law.
  • b.A straight conductor carries an increasing current from A to B, with a circular loop above it in the same plane. Find the direction of the current induced in the loop, and give your reasoning.
  • c.A rectangular metal frame PQRS, 4.0 cm wide (QR) and 7.0 cm tall (PQ), stands in a vertical plane in a uniform horizontal magnetic field of 4.5 × 10⁻³ T, directed along QR. A current of 2.5 A flows round it, up RS, along RQ and down QP. If the frame turns with a steady angular velocity ω about a vertical axis through its middle, obtain an expression for the e.m.f. induced in it.
  • d.Calculate the force on the side PQ.
  • e.Why does the side QR feel no force?
Hint

c. At the start the field lies in the frame’s plane: Φ = 0. As it turns through θ = ωt, the flux is BA sin ωt.

Answer
  • a.The induced current always flows in such a direction as to oppose the change that produces it.
  • b.Above the wire, the field of a current from A to B points out of the page (right-hand grip rule), and it is growing. The induced current opposes the growth, so its field inside the loop points into the page: the current is clockwise.
  • c.The frame’s area is A = 4.0 × 7.0 cm² = 28 cm² = 2.8 × 10⁻³ m². At the start the field lies along the frame’s plane, so no flux passes through it. After turning through θ = ωt, the flux is Φ = BA sin ωt, and

ε=−dΦdt=−BAωcos⁡ωt \varepsilon = -\frac{d\Phi}{dt} = -BA\omega\cos\omega t
an alternating e.m.f. of peak value
ε0=BAω=4.5×10−3×2.8×10−3×ω=1.26×10−5 ω V \varepsilon_0 = BA\omega = 4.5 \times 10^{-3} \times 2.8 \times 10^{-3} \times \omega = 1.26 \times 10^{-5}\,\omega\ \text{V}
(ω in rad/s). While the frame stands still, the flux doesn’t change and no e.m.f. is induced, whatever current flows in it.
d. PQ (7.0 cm) is at right angles to the field:
F=BIl=4.5×10−3×2.5×0.070=7.9×10−4 N F = BIl = 4.5 \times 10^{-3} \times 2.5 \times 0.070 = \mathbf{7.9 \times 10^{-4}\ N}
By Fleming’s left-hand rule it acts at right angles to the plane of the frame (out of the page for the current flowing down QP with the field to the right); the force on RS is equal and opposite, so the frame tends to turn.
e. QR carries current along the direction of the field (parallel or antiparallel to it). The force on a current is F = BIl sin θ, and with θ = 0° or 180°, sin θ = 0: no force.

13.

Lenz’s law gives the direction of an induced e.m.f.

  • a.Explain how Lenz’s law agrees with the conservation of energy.
  • b.A straight vertical conductor carries an increasing current from P (below) to Q (above), with a circular loop to its right in the same plane. Find the direction of the current induced in the loop, and give your reasoning.
  • c.What is called the electrical inertia of a circuit? Find its expression for a solenoid.
  • d.What is the electrical inertia of a straight conductor?
  • e.A wheel with metal spokes 1.2 m long turns in a magnetic field of flux density 5 × 10⁻⁵ T at right angles to its plane. An e.m.f. of 10⁻² V is induced between the rim and the axle. Find the rate of rotation of the wheel.
Answer
  • a.The induced current opposes the motion (or change) that causes it, so mechanical work must be done against a magnetic force to keep the change going. This work is converted into the electrical energy of the induced current. If the induced current aided the change instead, the motion would speed itself up and produce electrical energy from nothing, breaking the conservation of energy. So Lenz’s law is required by the conservation of energy.
  • b.To the right of a wire carrying current upwards, its field points into the page (right-hand grip rule), and it is growing. The induced current opposes the growth, so its field inside the loop points out of the page: the current is anticlockwise.
  • c.Self-induction (self-inductance L) is called the electrical inertia of a circuit, since it opposes any change of current, as mass opposes any change of velocity. For a solenoid of N turns, area A and length l, B = μ₀NI/l, the flux linkage is NBA = μ₀N²IA/l = LI, so

L=μ0N2Al L = \frac{\mu_0 N^2 A}{l}

  • d.A straight conductor links almost none of its own flux, so its self-inductance is very small, practically zero (taken as zero).
  • e.Each spoke turns about one end: ε = ½Bωr², so

ω=2εBr2=2×10−25×10−5×1.22=278 rad/s,f=ω2π=44 rev/s \omega = \frac{2\varepsilon}{Br^2} = \frac{2 \times 10^{-2}}{5 \times 10^{-5} \times 1.2^2} = 278\ \text{rad/s}, \qquad f = \frac{\omega}{2\pi} = \mathbf{44\ rev/s}

14.
  • a.State Faraday’s quantitative law of electromagnetic induction.
  • b.State and explain Lenz’s law.
  • c.A solenoid S is wound on a soft iron core. A coil C of 120 turns is wound on one end of the core; its area of cross-section is 1.5 cm². A Hall probe is close to the other end of the core. When there is a constant current in S, the flux density in the core is 0.19 T, and the voltmeter connected to the Hall probe reads 0.20 V. The current in S is now reversed in 0.13 s, at a constant rate.
  • i.Calculate the reading of the voltmeter connected to coil C while the current is changing.
  • ii.Copy and complete the table of voltmeter readings before, during (at the instant the current is zero) and after the reversal.
before the current changes during the change, when the current is zero after the current changes
voltmeter on coil C (V) … … …
voltmeter on the Hall probe (V) 0.20 … …
Hint

c. i. Reversing the field changes the flux through each turn from +BA to −BA: a change of 2BA.

Answer
  • a.The magnitude of the e.m.f. induced in a circuit is directly proportional to the rate of change of the magnetic flux linked with it: ε=−N dΦdt \varepsilon = -N\,\dfrac{d\Phi}{dt} .
  • b.Lenz’s law: the induced current flows in such a direction as to oppose the change that produces it. For example, when the north pole of a magnet approaches a coil, the induced current makes the near end of the coil a north pole, which repels the magnet; when the magnet moves away, the near end becomes a south pole, which attracts it. So work must be done to move the magnet either way, and this work becomes the electrical energy of the induced current, as the conservation of energy demands.
  • c.i. B = 0.19 T, A = 1.5 cm² = 1.5 × 10⁻⁴ m², N = 120, t = 0.13 s. The flux through each turn changes from +BA to −BA:

ΔΦ=2BA=2×0.19×1.5×10−4=5.7×10−5 Wb \Delta\Phi = 2BA = 2 \times 0.19 \times 1.5 \times 10^{-4} = 5.7 \times 10^{-5}\ \text{Wb}
ε=N ΔΦt=120×5.7×10−50.13=0.053 V \varepsilon = \frac{N\,\Delta\Phi}{t} = \frac{120 \times 5.7 \times 10^{-5}}{0.13} = \mathbf{0.053\ V}
ii. A Hall probe reads in proportion to the flux density (and its direction); coil C reads only while the flux changes:

before the current changes during the change, when the current is zero after the current changes
voltmeter on coil C (V) 0 0.053 0
voltmeter on the Hall probe (V) 0.20 0 −0.20

The flux changes at a steady rate throughout the reversal, so coil C reads a steady 0.053 V all through it, including the instant the field is zero.

15.

A solenoid is connected in series with a battery and a switch. A small coil, connected to a sensitive ammeter, is placed near one end of the solenoid, on its axis. As the current in the solenoid is switched on, there is a changing magnetic field inside the solenoid.

  • a.i. State Faraday’s qualitative law of electromagnetic induction.
  • ii.Explain how to find the direction of the magnetic field inside the solenoid (arrow P on the axis).
  • b.As the current in the solenoid is switched on, a current is induced in the small coil, and it gives rise to a magnetic field in the small coil.
  • i.Lenz’s law governs the direction of the induced current. Which fundamental principle of physics is it based on?
  • ii.Use Lenz’s law to state and explain the direction of the magnetic field due to the induced current in the small coil.
  • c.The small coil has an area of cross-section 7.0 × 10⁻⁴ m² and 75 turns. A constant current in the solenoid makes a uniform field of flux density 1.4 mT throughout the small coil. The direction of the current in the solenoid is reversed in 0.12 s. Calculate the average e.m.f. induced in the small coil.
Answer
  • a.i. Whenever the magnetic flux linked with a closed circuit changes, an e.m.f. is induced in the circuit.
  • ii.By the right-hand grip rule: curl the fingers of your right hand round the solenoid in the direction the current flows in its turns; your thumb points along the axis in the direction of the field inside (arrow P). The end the field comes out of is the solenoid’s north pole.
  • b.i. The conservation of energy.
  • ii.As the solenoid’s current grows, its field through the small coil, in the direction P, grows. By Lenz’s law the induced current opposes this increase, so the field it makes inside the small coil points opposite to P, back towards the solenoid. (The small coil’s face towards the solenoid becomes a like pole, repelling it.)
  • c.Reversing the field changes the flux through each turn from +BA to −BA, by 2BA:

ε=N×2BAt=75×2×1.4×10−3×7.0×10−40.12=1.47×10−40.12=1.2×10−3 V \varepsilon = \frac{N \times 2BA}{t} = \frac{75 \times 2 \times 1.4 \times 10^{-3} \times 7.0 \times 10^{-4}}{0.12} = \frac{1.47 \times 10^{-4}}{0.12} = \mathbf{1.2 \times 10^{-3}\ V}
(1.2 mV).

16.
  • a.An ideal transformer has a primary coil of 2700 turns and a secondary coil of 450 turns on a soft iron core, with a load resistor connected to the secondary. Explain why, when there is an alternating current in the primary coil, there is a current in the load resistor.
  • b.A step-down transformer is used on a 220 V line to supply a current of 0.5 A to a 15 W bulb. If the secondary has 20 turns, find the number of turns in the primary and the current in the primary.
Answer
  • a.The alternating current in the primary makes an alternating magnetic flux in the soft iron core. The core carries this flux through the secondary coil, so the flux linked with the secondary keeps changing. By Faraday’s law an alternating e.m.f. is induced in the secondary (mutual induction), and since the secondary and the load resistor form a closed circuit, it drives an alternating current through the resistor. (Here the secondary e.m.f. is 450/2700 = 1/6 of the primary’s.)
  • b.The bulb gets 15 W at 0.5 A, so the secondary voltage is

ES=PIS=150.5=30 V E_S = \frac{P}{I_S} = \frac{15}{0.5} = 30\ \text{V}
NP=NS×EPES=20×22030=146.7≈147 turns N_P = N_S \times \frac{E_P}{E_S} = 20 \times \frac{220}{30} = 146.7 \approx \mathbf{147\ turns}
For an ideal transformer the input power equals the output, 15 W:
IP=15220=0.068 A I_P = \frac{15}{220} = \mathbf{0.068\ A}

17.

A straight electrical conductor is placed between the poles of a U-shaped magnet (Figure 18.31). The field in the gap is horizontal, from one pole to the other, and the conductor lies across it. The ends of the conductor are connected to a voltmeter.

  • a.Name a material an electrical conductor can be made from.
  • b.i. The voltmeter measures the e.m.f. across the conductor. State the unit of e.m.f.
  • ii.State what, if anything, the meter shows when the conductor is moved: horizontally, from side to side, between the poles (towards one pole and then the other); vertically, up and down, between the poles.
  • c.State two factors that affect the size of the e.m.f. across the conductor.
Answer
  • a.Copper (or aluminium).
  • b.i. The volt (V).
  • ii.Side to side, towards one pole and back: the conductor moves along the field lines and cuts none of them, so no e.m.f. is induced: the meter shows zero.

Up and down: the conductor moves across the field lines and cuts them, so an e.m.f. is induced and the pointer deflects. It deflects one way while the conductor moves up and the other way while it moves down, so it swings backwards and forwards as the conductor is moved up and down.
c. Any two of: the strength of the magnet (B); the speed of the conductor (how fast it moves across the field); the length of conductor in the field (ε = Blv).

18.
  • a.A teacher hangs a bar magnet, north pole down, from a spring above a coil connected to a center-zero millivoltmeter. The teacher pulls the magnet down until its lower end is inside the coil, and releases it. The magnet moves up and down again and again, its end entering and leaving the coil. Describe and explain the readings on the millivoltmeter.
  • b.Electricity from a power station at 22 000 V is sent along a 132 000 V line to homes that use 240 V. Name the device used at X (between the station and the line) and at Y (between the line and the homes).
Answer
  • a.As the north pole moves down into the coil, the flux through the coil increases, an e.m.f. is induced, and the needle moves one way. As it moves up and out, the flux decreases and the needle moves the other way. So the needle swings to and fro as the magnet bounces. It is largest when the magnet moves fastest (in the middle of its motion), and it passes zero at the top and bottom of each bounce, where the magnet is momentarily at rest and the flux is not changing (as at the spring’s greatest stretch). Each swing is a little smaller than the last as the bounce dies away: the induced current also opposes the magnet’s motion, taking energy from it.
  • b.X: a step-up transformer (22 kV to 132 kV). Y: a step-down transformer (132 kV to 240 V).
19.

A small rectangular coil ABCD has 140 turns of wire. Its sides AB and BC are 4.5 cm and 2.8 cm long. The coil is held between the poles of a large magnet so that it can turn about an axis through its center, parallel to AB. The magnet makes a uniform field of flux density B between its poles. When the current in the coil is 170 mA, the greatest torque on the coil is 2.1 × 10⁻³ N m.

  • a.For the coil in the position of greatest torque, is the plane of the coil parallel to the field, or at right angles to it?
  • b.With the coil in that position, calculate the magnitude of the force on i. side AB, ii. side BC.
  • c.Use your answer to b.i. to show that B is 70 mT.
  • d.i. State Faraday’s law of electromagnetic induction.
  • ii.The current in the coil is switched off, and the coil is left as in Figure 18.34, its plane parallel to the field. It is then turned through 90° in 0.14 s. Calculate the average e.m.f. induced in the coil.
Hint

b. i. Torque = force on AB × its distance from the axis, plus the same for CD: τ = F × BC.

Answer
  • a.Parallel to the field. Then AB and CD are at right angles to the field, and the forces on them, at right angles to the coil, have the greatest lever arm.
  • b.i. The torque comes from two equal and opposite forces F, on AB and on CD, each at BC/2 from the axis: τ = F × BC. So

F=τBC=2.1×10−30.028=7.5×10−2 N F = \frac{\tau}{BC} = \frac{2.1 \times 10^{-3}}{0.028} = \mathbf{7.5 \times 10^{-2}\ N}

  • ii.BC lies along the field (θ = 0), so the force on it is BIl sin 0° = zero.
  • c.The force on AB, with 140 turns, is F = NBIl, so

B=FNIl=7.5×10−2140×0.170×0.045=0.070 T=70 mT B = \frac{F}{NIl} = \frac{7.5 \times 10^{-2}}{140 \times 0.170 \times 0.045} = 0.070\ \text{T} = \mathbf{70\ mT}
(Or from the greatest torque, τ = BINA: B = 2.1 × 10⁻³ ÷ (0.170 × 140 × 0.045 × 0.028) = 0.070 T.)

  • d.i. The e.m.f. induced in a circuit is proportional to (in SI units, equal to) the rate of change of the magnetic flux linkage: ε=−N dΦ/dt \varepsilon = -N\,d\Phi/dt .
  • ii.The flux through each turn rises from 0 (plane parallel to the field) to BA (plane at right angles to it):

Δ(NΦ)=NBA=140×0.070×0.045×0.028=1.23×10−2 Wb \Delta(N\Phi) = NBA = 140 \times 0.070 \times 0.045 \times 0.028 = 1.23 \times 10^{-2}\ \text{Wb}
ε=1.23×10−20.14=8.8×10−2 V=88 mV \varepsilon = \frac{1.23 \times 10^{-2}}{0.14} = 8.8 \times 10^{-2}\ \text{V} = \mathbf{88\ mV}

20.

A simple a.c. generator has a coil that turns between the poles of a magnet, its ends joined to two slip rings. When the coil turns, an e.m.f. is induced in it.

  • a.Explain why an e.m.f. is induced.
  • b.State the purpose of the slip rings.
  • c.The direction of the current in the coil can be found from Lenz’s law. State and explain Lenz’s law.
  • d.The induced e.m.f. can be increased by turning the coil faster. State two other ways in which it can be increased.
Answer
  • a.As the coil turns, the angle between its plane and the field keeps changing, so the magnetic flux through it (BA cos θ) keeps changing; its sides cut the field lines. By Faraday’s law, a changing flux linkage induces an e.m.f.
  • b.The slip rings turn with the coil, each always joined to the same end of it. The brushes pressing on them connect the turning coil to the fixed external circuit, without the wires twisting, so the alternating e.m.f. reaches the circuit.
  • c.The induced current flows in such a direction as to oppose the change that produces it. In the generator, the current in the coil makes forces on its sides that oppose its rotation, so the engine or turbine must do work to keep it turning; that work becomes the electrical energy delivered, as the conservation of energy requires.
  • d.Any two of: use more turns in the coil; use a stronger magnet (or wind the coil on a soft iron core); use a coil of larger area (ε₀ = NBAω).
21.

A farmer connects a house to the mains. The house is a long way from the nearest 230 V supply, and is joined to it by long cables.

  • a.The farmer uses 230 V lamps in the house, but they do not light up at full brightness. Explain why the lamps are dim.
  • b.The farmer then adds a transformer A next to the supply and a transformer B next to the house. Now the lamps light up at full brightness. Explain why.
  • c.The 230 V supply provides 690 W of power to transformer A.
  • i.Calculate the current supplied to the transformer.
  • ii.Calculate the energy supplied to the transformer in 10 minutes, in joules.
Answer
  • a.The long cables have a large resistance. The current to the lamps flows through it, so there is a large p.d. across the cables (IR), and the lamps get much less than 230 V. Energy is also wasted as heat in the cables (I²R). So the lamps are dim.
  • b.Transformer A is a step-up transformer: it raises the voltage and so lowers the current in the cables (for the same power). With a small current, the p.d. across the cables and the heat lost in them (I²Rt) are very small. Transformer B is a step-down transformer: it lowers the voltage back to 230 V at the house (raising the current), so the lamps get their full voltage and light at full brightness.
  • c.i. I=PV=690230=3 A I = \dfrac{P}{V} = \dfrac{690}{230} = \mathbf{3\ A}
  • ii.E=Pt=690×10×60=414 000 J=4.14×105 J E = Pt = 690 \times 10 \times 60 = 414\,000\ \text{J} = \mathbf{4.14 \times 10^5\ J} (414 kJ)