Why is there no mountain on Earth twice as tall as Sagarmatha (Everest)? Not because the Himalaya stopped rising: the plates are still pushing. The answer is in the rock at the bottom. Pile up enough rock and the rock underneath can no longer spring back: it starts to flow and crumble, and the mountain sinks and spreads. A pencil, a rough number for rock and one line of working put the limit at about 10 km. Sagarmatha, at 8,849 m, is close to it.
That is what this unit is about: how solids push back when we pull, squeeze or twist them, how far they can be pushed before they give way, and how much energy they store on the way. It is the physics behind every spring, every steel cable on a Nepali suspension bridge, every rubber band and every building that must ride out an earthquake.
8.1 Introduction
The force you apply in either case changes the size or shape of the body: it is a deforming force. While the body is deformed, a force sets up inside it that tries to bring it back to its original shape: the restoring force. When you remove the deforming force, the restoring force returns the body to its original size and shape.
Elasticity is the property of matter by which a body regains its original shape and size when the deforming force is removed.
Pull the spring hard enough and it doesn’t come back: it stays longer, with its coils pulled open. It has been stretched beyond its elastic limit, the greatest deformation (or deforming force) from which it can still recover completely. Beyond it the body is permanently deformed: it is in the plastic stage (engineers say damaged, or yielded). Plasticity is the property of a body by which it keeps its new shape after the deforming force is removed.
Where elasticity comes from
Every solid is made of atoms held near one another by electric forces. Two neighboring atoms sit at the separation r₀ where the attraction between them and their repulsion balance: the equilibrium separation, about 0.1 to 0.3 nm.
- Pull them apart a little (separation more than r₀), and the attraction wins: a force pulls them back.
- Push them together (separation less than r₀), and the repulsion wins: a force pushes them apart.
So each bond behaves like a tiny spring, and a solid is a three-dimensional net of such springs. Stretch the solid and you stretch billions of bonds a tiny bit each; their restoring forces add up to the restoring force you feel. This is why elasticity comes from short-range forces between molecules.
Two things follow from the curve:
- Near r₀ the curve is nearly straight, so for small deformations the restoring force is proportional to the deformation. That is Hooke’s law (Section 8.2).
- The attraction has a greatest value. Pull harder than that and the bonds can no longer pull the atoms back. In a metal, what really happens is that whole layers of atoms slip past one another into new places and stay there: that is plastic deformation. Pull harder still and the solid breaks.
A copper wire is stretched beyond its elastic limit and the load is then removed. The wire:
Pick an answer to see why.
Elasticity in use
- Springs are made of steel, not copper. A spring balance must give the same reading for the same load every time, so its spring must spring back exactly and must not take a permanent set. Steel is more elastic than copper (it needs a greater force for the same extension) and has a much higher elastic limit, so a steel spring stays true far longer.
- Steel rods in reinforced concrete (RCC). Concrete is strong when squeezed but cracks easily when pulled; the steel bars cast inside it carry the pulling forces. In an earthquake a building sways back and forth. Within their elastic limit the bars spring back each time; and if a shock is so strong that they go past it, good steel bars bend and stretch (they are ductile, Section 8.7) instead of snapping, so the building holds together long enough for people to get out. That is why Nepal’s building code asks for proper steel bars, bent hooks and closely spaced rings (ties) round them.
- Twisted (stranded) cables. High-tension power lines and crane ropes are made of many thin wires twisted together, not one thick rod. A thin wire bends with little strain, so the cable is flexible and doesn’t kink; if one strand cracks, the others still hold; and thin strands suffer less from metal fatigue (Section 8.8) than a solid rod.
8.2 Hooke’s law
Hang a spring from a hook and add loads one at a time, measuring the extension each time. Within the elastic limit you find that equal loads give equal extensions: the extension is directly proportional to the load. This is Hooke’s law:
Within the elastic limit, the extension of a body is directly proportional to the force (load) applied to it.
The spring pulls back on whatever stretches it with a force of the same size, towards its natural length, opposite to the extension, so the restoring force is
The constant k is the force constant (or spring constant, or stiffness): the force needed per unit extension. Its unit is the newton per meter, N/m. A stiff spring has a large k; a soft one, a small k.
From a spring to a wire: stress and strain
A wire obeys the same law, but its force constant depends on its size: a longer wire stretches more under the same load (every part of it stretches, and the stretches add up), and a thicker wire stretches less (the load is shared by more bonds). For a wire of length L and cross-sectional area A, turns out to be proportional to , and it helps to take the size out:
Here , the force per unit area, is the stress, and , the extension per unit length, is the strain. For a given material is the same whatever the wire’s size, so stress ∝ strain:
E is the modulus of elasticity of the material. So Hooke’s law can also be stated:
Within the elastic limit, stress is directly proportional to strain.
The first form is about one particular spring or wire; this second form is about the material, whatever its shape. Compare: k for a wire is .
Two springs stretch 2 cm and 5 cm under the same load. Which has the larger force constant?
Pick an answer to see why.
Experimental verification
Two long, identical wires are hung side by side from the same rigid support (Figure 8.5):
- the reference wire A carries the main scale M and a small constant load that keeps it straight;
- the experimental (test) wire B carries a vernier scale V, just beside M, and a hanger for loads.
Why two wires? If the support sags a little under the load, or the room warms up and both wires expand, both scales move together and the reading doesn’t change. The vernier measures only how much B stretches more than A, which is the extension caused by the load.
- With only a small starting load on B (to take the kinks out), note the vernier reading.
- Add equal loads (say 0.5 kg or 1 kg) one at a time, waiting a minute after each, and note the reading each time. Stay well within the elastic limit.
- Then take the loads off one at a time, noting the readings again (they should match the first set, showing the wire has not taken a permanent set).
- For each load, the extension is the reading minus the starting reading; take the mean of the loading and unloading values.
Plotting load against extension gives a straight line through the origin: the extension is proportional to the load, , so and, dividing by A and L as above, stress ∝ strain. Hooke’s law is verified. (The same apparatus measures the Young’s modulus of the wire, Section 8.4.)
8.3 Stress, strain, elasticity and plasticity
Stress
When a body is deformed, the restoring force inside it acts across every section of it. The restoring force per unit area is the stress. When the body is in equilibrium, the restoring force equals the applied force, so in practice
Its SI unit is the newton per square meter, N/m², also called the pascal (Pa); its dimensions are [ML⁻¹T⁻²], the same as pressure.
Stress and pressure are both a force per unit area, but they are not the same thing:
- Pressure is the push of a fluid (a liquid or a gas) on a surface. At any point in a fluid at rest it is the same in every direction, and it is always a push, at right angles to the surface. It is a scalar.
- Stress is the force per unit area inside a solid, set up by stretching, squeezing, shearing, twisting or bending it. It can pull as well as push, it can act along a surface as well as across it, and at one point its size depends on which way the surface faces.
Types of stress
Stress is named by the direction of the force relative to the surface it acts on.
1. Normal stress: the force acts at right angles (normal) to the surface. It is of two kinds:
- Tensile stress: the forces pull outwards along the length, and the body gets longer (a crane’s cable, a bridge’s hangers, a guitar string).
- Compressive stress: the forces push inwards along the length, and the body gets shorter (a pillar, the legs of a table, your thigh bone).
When a body is squeezed from all sides equally, as a stone at the bottom of a lake is, the normal stress is the same everywhere: it is the pressure, and it changes the body’s volume. This is the stress of the bulk modulus (Section 8.4).
2. Tangential (shearing) stress: the force acts along (parallel to) the surface. Hold the bottom face of a thick book flat on a table and push its top cover sideways: the book leans over, its pages sliding over one another. The force per unit area of the face it acts on is the tangential or shearing stress.
In Figure 8.8 the tangential force F acts along the upper face AB while the lower face CD stays fixed. A moves to A′ and B to B′, with AA′ = BB′ = x. The shearing stress is , where A is the area of the face AB (the area under shear).
Your fingers rub a whiteboard eraser across the board. The stress in the eraser’s felt, where it touches the board, is mainly:
Pick an answer to see why.
Strain
A deforming force changes the body’s length, volume or shape. Strain is the change in a dimension divided by the original value of that dimension:
It is a ratio of two quantities of the same kind, so it has no unit and no dimensions. A strain of 0.001 means a change of one part in a thousand, 0.1%.
There are three kinds, one for each kind of change.
i. Longitudinal (tensile or compressive) strain: the change in length per unit original length.
A steel wire 2 m long that stretches by 1 mm has a strain of 0.001/2 = 0.0005, a twentieth of one percent. Metals almost never take a strain of more than a few tenths of a percent before they yield: that is why the extensions in this unit are millimeters.
ii. Volumetric (volume) strain: the change in volume per unit original volume. If a volume V decreases by ΔV,
The minus sign is there because a pressure from all sides makes the volume smaller (ΔV is negative), and we want the strain to be a positive number.
iii. Shear strain: under a shearing stress the upper face moves sideways by x relative to the fixed lower face, a distance L below it, and the body leans over by the angle of shear φ (Figure 8.8). The shear strain is
For metals, stone and wood φ is tiny (a fraction of a degree), so , and the shear strain is simply the angle of shear, in radians.
A rubber block 5.0 cm thick is fixed at its base. A sideways force on its top face moves the top by 2.0 mm. Its shear strain is:
Pick an answer to see why.
Elasticity and plasticity
As in Section 8.1, elasticity is the property of a body by which it regains its original shape and size after the deforming force is removed.
- A perfectly elastic body would regain its original shape and size completely and immediately after the force is removed, however large the force. No real body is perfectly elastic; quartz fiber and phosphor bronze come closest.
- A perfectly plastic body doesn’t regain its original shape at all, however small the force. Paraffin wax, putty and wet clay are close to perfectly plastic: a potter in Bhaktapur’s Pottery Square counts on it.
Applications of elasticity
- Cranes and lifts. The steel rope of a crane must never be stretched beyond its elastic limit. Knowing the elastic limit of the steel and the greatest load, engineers work out the cross-sectional area the rope needs (the worked example on the lift cable in Section 8.4).
- How high a mountain can be. The rock at the base of a mountain carries the weight of all the rock above it. A column of rock of height h and density ρ presses on its base with a stress . When that stress passes the rock’s elastic limit, the rock at the bottom yields and flows, and the mountain sinks. So the greatest height is about (worked out below).
- Bridges and buildings. A bridge is designed, from the elasticity of its materials, so that under its own weight, the heaviest traffic and the strongest wind it neither sags too far nor breaks, and every part stays well within its elastic limit.
Elastic limit
The elastic limit is the greatest stress (or load) a body can take and still regain its original shape and size completely when the stress is removed. Beyond it the body is permanently deformed.
Engineers never load a part up to its elastic limit. They allow only a fraction of it, often one-third or less: the ratio of the elastic limit (or breaking stress) to the greatest stress allowed is the factor of safety. It covers flaws in the material, loads larger than expected, wear, rust and fatigue.
Modulus of elasticity
From Hooke’s law, stress ∝ strain, so
E is the modulus of elasticity of the material: the stress needed per unit strain. Since strain has no unit, E has the unit of stress, N/m² or Pa. A material with a large modulus needs a large stress for a small strain: it is stiff, or “highly elastic” in the physicist’s sense.
8.4 Moduli of elasticity
A body can be stretched (its length changes), squeezed from all sides (its volume changes) or sheared (its shape changes). Each kind of stress and its strain give a modulus.
a. Young’s modulus
The Young’s modulus (Y) of a material is the ratio of the normal stress to the longitudinal strain it produces, within the elastic limit. It describes how a material resists a change in length.
For a wire of length L and cross-sectional area A stretched by x by a force F (Figure 8.9):
Turned round, : a wire stretches more if it is longer, thinner, more heavily loaded, or made of a material with a smaller Y. For a round wire of diameter d, , so halving the diameter makes the extension four times as large.
| Material | Young’s modulus (N/m²) |
|---|---|
| Steel | 2.0 × 10¹¹ |
| Copper | 1.1–1.3 × 10¹¹ |
| Brass | about 1.0 × 10¹¹ |
| Aluminium | 7.0 × 10¹⁰ |
| Glass | about 7 × 10¹⁰ |
| Bone (along its length) | about 1.7 × 10¹⁰ |
| Wood (along the grain) | about 1 × 10¹⁰ |
| Nylon | about 3 × 10⁹ |
| Rubber | about 10⁶ to 10⁷ |
Two things to know about Young’s modulus:
- It falls as the temperature rises. In a hot metal the atoms vibrate harder and sit a little farther apart, where the bonds pull back less strongly for the same extra stretch. So the same stress gives a larger strain, and Y is smaller.
- A wire stretches under its own weight. A uniform wire of mass m, length L, area A and Young’s modulus Y hanging from a ceiling stretches by , half of what it would stretch if its whole weight hung from its lower end. The derivation is in exercise question 9.
b. Bulk modulus
The bulk modulus (B) is the ratio of the normal stress (the pressure from all sides) to the volumetric strain it produces, within the elastic limit. It describes how a material resists a change in volume (Figure 8.10).
If a pressure increase P makes a volume V decrease by ΔV,
The minus sign makes B positive, since ΔV is negative when P is positive. Solids, liquids and gases all have a bulk modulus, since all of them resist being squashed (a fluid has no fixed length or shape, so only the bulk modulus applies to it).
The reciprocal of the bulk modulus is the compressibility, : the fractional change in volume per unit increase of pressure, in Pa⁻¹. A material with a large bulk modulus is hard to compress.
| Material | Bulk modulus (N/m²) |
|---|---|
| Steel | about 1.6 × 10¹¹ |
| Glass | about 4 × 10¹⁰ |
| Water | 2.2 × 10⁹ |
| Air, at constant temperature | about 1 × 10⁵ (equal to its pressure) |
- Water’s bulk modulus is about 20,000 times air’s: water is far harder to compress, so in the physicist’s sense water is far more elastic than air. That is why hydraulic brakes use oil or brake fluid: an air bubble in the pipes makes the brake pedal spongy.
- Well-compacted concrete has very few air spaces left in it, so it is hard to compress: its compressibility is low and its bulk modulus high.
c. Modulus of rigidity (shear modulus)
The modulus of rigidity (η, eta), or shear modulus, is the ratio of the tangential stress to the shear strain it produces, within the elastic limit. It describes how a material resists a change in shape (Figure 8.8).
where φ = x/L is the angle of shear in radians. Only solids have a modulus of rigidity: a liquid at rest can’t hold a shearing stress at all (push sideways on the top of some water and it simply flows). For steel η is about 8 × 10¹⁰ N/m², a little less than half its Young’s modulus.
Which modulus does a liquid not have?
Pick an answer to see why.
Experimental determination of Young’s modulus
The apparatus is the one used to verify Hooke’s law (Figure 8.5): two wires A and B, both hung from a rigid support, with small starting loads to take the kinks out. A main scale M is fixed to the reference wire A, and a vernier scale V to the experimental wire B, just beside M.
- Measure the length L of wire B from the support to the vernier with a meter rule.
- Measure its diameter d with a screw gauge at several places along it, in two directions at right angles each time, and take the mean. Then .
- Add loads of 1 kg (or 0.5 kg) one at a time, within the elastic limit, noting the vernier reading after each; then take them off one at a time and note the readings again.
- Plot the load F against the extension x. The graph is a straight line through the origin; find its slope, .
Then, since the tensile stress is and the tensile strain ,
Why a long, thin wire? Because : a long wire stretches more, and a thin one more still, so the tiny extension becomes large enough to measure. The diameter needs the most care: it is small, and it is squared in A, so a 1% error in d gives a 2% error in Y.
8.5 Elastic potential energy
When you stretch a wire, you do work against its restoring force. If the wire stays within its elastic limit, this work isn’t lost: it is stored in the stretched bonds as elastic potential energy, and you get it back when the wire springs back (by the work–energy theorem, Unit 5). A drawn bow, a wound clock spring and a stretched catapult all store energy this way.
The energy stored in a stretched wire
Take a wire of length L and cross-sectional area A, fixed at its top (Figure 8.9). A force at its lower end stretches it slowly by x.
The force grows with the extension. At an extension x′ (on the way to x), Y = (F/A)/(x′/L), so the force is
Work for a small extra stretch. Stretching it a little more, by dx′, the force hardly changes, so the work done is
Add up the work from 0 to x (integrate):
Write it with the final force. At the end, the force is , so :
The half is there because the force grows steadily from 0 to F as the wire stretches: on average it is only .
Graphical method
Plot the force F needed to stretch a spring (or wire) against its extension x. Within the elastic limit it is a straight line through the origin whose slope is the force constant k (F = kx; the spring’s own restoring force is −kx). Equal loads give equal steps of extension.
As in Unit 5, the work done by a force is the area under its force–extension graph. Here the area is a triangle:
This is the elastic potential energy stored, the same result as before (with ).
Energy density
The energy stored per unit volume of the stretched wire is its energy density. The wire’s volume is AL, so
and since stress = Y × strain,
So the energy stored per unit volume is proportional to the square of the strain: stretch it twice as far, store four times the energy.
- A compressed spring dropped into acid. A spring held squeezed by a thread stores elastic potential energy. If it is dissolved in acid, the energy doesn’t vanish: it ends up as extra random motion of the acid’s molecules, so the acid gets very slightly warmer than it would with an unsqueezed spring.
- A catapult. A stretched catapult stores elastic potential energy. When it is released, the energy goes into the kinetic energy of the stone (exercise question 21).
A wire stores 2 J when it is stretched by 1 mm. Within the elastic limit, how much does it store when it is stretched by 3 mm?
Pick an answer to see why.
8.6 Poisson’s ratio
Stretch a rubber band and it gets thinner as well as longer; squash a ball of dough and it bulges out sideways. Almost every material does the same, only far less visibly: a wire that is stretched becomes slightly thinner, and a rod that is compressed becomes slightly fatter.
- The change in length per unit length, , along the force, is the longitudinal strain.
- The change in diameter per unit diameter, , at right angles to the force, is the lateral strain.
Within the elastic limit, the lateral strain is proportional to the longitudinal strain. The ratio of the lateral strain to the longitudinal strain is Poisson’s ratio, σ (sigma):
where ΔD is the decrease in diameter when the length increases by x. (Written with signs, the lateral strain is −ΔD/D, opposite in sign to x/L, and σ = −(lateral strain)/(longitudinal strain), which comes to the same positive number.) It is a ratio of two strains, so it has no unit.
| Material | Poisson’s ratio |
|---|---|
| Cork | about 0 |
| Concrete | about 0.1–0.2 |
| Glass | about 0.2–0.25 |
| Steel | about 0.3 |
| Copper | about 0.34 |
| Rubber | nearly 0.5 |
How the volume changes
A wire of diameter D and length L has volume . When it stretches, its length grows by the fraction (the strain ε, epsilon) and its diameter shrinks by the fraction . For small changes, the fractional change in a product is the sum of the fractional changes of its factors (D counts twice, since it is squared):
- If σ were exactly 0.5, the volume wouldn’t change at all: rubber, with σ close to 0.5, keeps almost the same volume however it is stretched.
- For σ below 0.5 the volume grows a little when the wire is stretched. A σ above 0.5 would make a stretched wire shrink in volume, which no material does (it would mean squeezing it from all sides made it bigger), so σ can never be more than 0.5; for ordinary materials it lies between 0 and 0.5.
- Cork, with σ about 0, hardly gets fatter when squeezed along its length. That is why a cork can be pushed into a bottle’s neck: rubber, which bulges sideways when pushed, jams.
A wire of a material with Poisson’s ratio 0.25 is stretched by a strain of 0.002. Its volume:
Pick an answer to see why.
8.7 The stress–strain curve
Clamp a metal wire (or a test bar) in a machine that pulls its ends apart slowly, measuring the stress and the strain all the way until it breaks. The graph of stress against strain is the material’s stress–strain curve. For a ductile metal such as mild steel it has these parts (Figure 8.15).
- O to A: Hooke’s law. The graph is a straight line: stress is proportional to strain. A is the proportional limit. The slope of OA is the Young’s modulus.
- A to B: still elastic. The line curves a little: stress is no longer proportional to strain, but if the load is removed the wire still comes back to its original length. B is the elastic limit; for mild steel it is also the upper yield point, and A and B are very close together.
- B to C: yielding. Past B the wire yields: it suddenly stretches without needing more stress (the stress even drops a little, to the lower yield point C). If the load is removed now, the wire doesn’t return to its original length: it keeps a permanent set. Between B and C the wire is partly elastic and partly plastic, and C is often called simply the yield point.
- C to D: plastic flow and strain hardening. The wire stretches a great deal, and it takes a rising stress to stretch it further: the metal becomes harder as it is worked, which is called strain hardening. D is the greatest stress the wire can take: the ultimate tensile stress (or tensile strength). Some books call D the breaking stress, since it is the greatest stress before breaking.
- D to E: necking and fracture. Past D the wire starts to get thinner at one weak place, a neck. All further stretching happens in the neck, so a smaller and smaller load stretches it, and it breaks at E, the fracture point. (The stress here is worked out on the original area; the true stress in the shrinking neck is still rising.)
Ductile and brittle materials
- Ductile materials have a long plastic region between the elastic limit and fracture: they stretch a long way, plastically, before they break. Most metals (copper, mild steel, aluminium, gold, silver) are ductile; that is what lets them be drawn into wires, bent into shape and hammered into sheets. A long plastic region means great ductility.
- Brittle materials break soon after (or at) the elastic limit, with almost no plastic region. Glass, cast iron, chalk, concrete and pottery are brittle: they snap instead of bending.
For bending a wire into shape, as for electric wiring, the steel bars of RCC or a jeweler’s gold, ductile materials are wanted.
Elastomers are materials that can be stretched to very large strains and still spring back, but that don’t obey Hooke’s law even within their elastic limit: their stress–strain curve is not a straight line anywhere. Rubber is the best-known elastomer: a rubber band can be stretched to five or six times its length and returns. Its long, coiled molecules straighten out as it stretches and curl back when it is released.
On the stress–strain curve of a ductile metal, the greatest stress the wire can bear is at:
Pick an answer to see why.
8.8 Elastic after-effect, hysteresis and fatigue
Elastic after-effect
Some bodies regain their shape as soon as the deforming force is removed; others take some time. The delay in regaining the original shape after the deforming force has been removed is the elastic after-effect.
- For quartz and phosphor bronze the after-effect is negligible; for glass fiber it is considerable. That is why the suspension fibers of moving-coil galvanometers and other sensitive instruments are made of quartz or phosphor bronze: after each deflection they must return to zero at once.
- A perfectly elastic body would have zero after-effect; a perfectly plastic (inelastic) body never returns at all, so its after-effect is, in effect, infinite.
Elastic hysteresis
Stretch a rubber band and let it go back, plotting the stress against the strain all the way. The graph on the way back (unloading) does not follow the graph on the way out (loading): for the same strain, the stress is lower while unloading. The band still returns to its original length, but along a different path. This lagging of the strain behind the stress is elastic hysteresis, and the closed figure the two curves make is the hysteresis loop.
The area under the loading curve is the work done on the rubber per unit volume; the area under the unloading curve is the work it gives back. The difference, the area of the loop, is energy that has not been stored but turned into heat inside the rubber, every cycle. So:
- Rubber absorbs vibration. Rubber mounts under engines and machines, and rubber pads (bearings) under bridges and some buildings, take in the energy of each shake and turn it into heat, because rubber has a large hysteresis loop.
- Tyres get warm. A tyre is squashed and released at every turn of the wheel; its hysteresis loss heats it, and is part of the rolling resistance that costs fuel.
- For a car’s suspension spring, or a watch’s balance spring, you want the opposite: steel, whose loop is so thin that almost all the energy comes back.
Elastic fatigue
Bend a paper clip back and forth: after a dozen or so bends it snaps, though no single bend was strong enough to break it. A material that is loaded and unloaded over and over, many thousands or millions of times, can crack and break at a stress well below its breaking stress, or even below its elastic limit. Tiny cracks start at a scratch, a sharp corner or a flaw, and grow a little with each cycle. This loss of strength under repeated stress is elastic fatigue (or fatigue failure), a little like a person who tires after doing the same work over and over.
Its effects:
- A wire can be broken by repeated bending even though the stress never reaches its breaking stress; it can even be cut into pieces by hand, with no tools, just by bending it back and forth at the same spot.
- After many years of service, railway tracks, bridges and aircraft are inspected for fatigue cracks, and replaced or declared unsafe.
- After long use, a spring balance’s spring gives wrong readings, because the spring has lost some of its elasticity.
Exercise
Choose the correct option
- Which modulus of elasticity do solids, liquids and gases all have?
Pick an answer to see why.
- A light steel wire of force constant k hangs from a ceiling. A mass m is attached to its lower end while held at the wire’s natural length, and then suddenly released. The greatest elongation of the wire is:
Pick an answer to see why.
- Which is the correct expression for Poisson’s ratio (R the radius and L the length of a wire)?
Pick an answer to see why.
- A rod is fixed between two rigid supports and then heated. The stress set up in the rod is:
Pick an answer to see why.
- Which of these has the highest elasticity?
Pick an answer to see why.
- How does Young’s modulus change when the temperature rises?
Pick an answer to see why.
- Substances that can be stretched to large strains and still spring back are called:
Pick an answer to see why.
- A shearing stress applied to a body changes its:
Pick an answer to see why.
- A uniform wire of mass m, length L, cross-sectional area A and Young’s modulus Y hangs from a ceiling. Its elongation under its own weight is:
Pick an answer to see why.
- Shearing strain is measured by the:
Pick an answer to see why.
- A ball’s volume decreases by 0.01% under a pressure of 100 atmospheres. The bulk modulus of its material is about:
Pick an answer to see why.
- The delay with which an elastic body regains its original shape after the deforming force is removed is called:
Pick an answer to see why.
Answer these questions
- a.State Hooke’s law.
- b.Does Hooke’s law apply to all materials?
- c.The elastic limit of steel is 8 × 10⁸ N/m² and its Young’s modulus is 2 × 10¹¹ N/m². What is the greatest elongation that can be given to a steel wire half a meter long without exceeding its elastic limit?
Answer
- a.Name the three moduli of elasticity.
- b.Which kind of elasticity does water have?
- c.A steel guitar string 80 cm long and 1.0 mm in diameter is tightened to a tension of 2000 N by turning a screw. How far is the string stretched? (Y for steel = 2.0 × 10¹¹ N/m²)
Answer
- a.What is meant by Poisson’s ratio?
- b.Define elastic after-effect.
- c.Find the increase in energy of a brass bar 0.5 m long, of cross-sectional area 1 × 10⁻⁴ m², when it is compressed along its length by a load of 5 kg. (Y for brass = 1.0 × 10¹¹ N/m², g = 10 m/s²)
Answer
- a.What is elastic potential energy? Derive an expression for the energy stored in a stretched wire.
- b.A uniform rod of a material with Poisson’s ratio 0.2 is given a longitudinal strain of 4 × 10⁻³. Find the percentage change in its volume.
- c.A copper wire of cross-sectional area 0.01 cm² is under a tension of 25 N. Find the decrease in its cross-sectional area. (Y for copper = 1.1 × 10¹¹ N/m², σ = 0.32)
Hint
Answer
- a.Discuss the different moduli of elasticity.
- b.What force would be needed to stretch a steel wire of cross-sectional area 1 × 10⁻⁴ m² to double its length, if Hooke’s law held that far? (Y for steel = 2.0 × 10¹¹ N/m²)
- c.A steel wire and a copper wire of equal cross-sectional area are joined end to end. When the combination is under tension, the two wires stretch by equal amounts. Find the ratio of the length of the steel wire to that of the copper wire. (Y for steel = 2.0 × 10¹¹ N/m², for copper 1.1 × 10¹¹ N/m²)
Answer
- a.What are the elastic limit and the breaking stress?
- b.Define elastic hysteresis.
- c.A sample of fishing line is 1.0 m long, with a circular cross-section of radius 0.25 mm. When a weight is hung on it, it stretches by 50 mm and the stress is 2.0 × 10⁸ Pa. Find i. its cross-sectional area, ii. the weight hung on it, iii. the strain, and iv. its Young’s modulus.
Answer
Numerical problems
Young’s modulus for steel is 2.0 × 10¹¹ N/m². Find the work done in stretching a steel wire 100 cm long, of cross-sectional area 0.030 cm², when a load of 100 N is slowly applied, without the elastic limit being reached.
Answer
A uniform steel wire of density 7800 kg/m³ has a mass of 16 g and is 2.50 m long. It stretches by 1.2 mm when pulled by a force of 80 N. Find a. the Young’s modulus of the steel and b. the energy stored in the wire.
Hint
Answer
The rubber cord of a catapult has a cross-sectional area of 1.0 mm² and an unstretched length of 10.0 cm. It is stretched to 12.0 cm and then released to throw a stone of mass 5.0 g. From energy considerations, or otherwise, find the speed with which the stone is thrown. (Y for rubber = 5.0 × 10⁸ N/m²)
Answer
A copper wire 1 m long and a steel wire 2 m long, of the same cross-sectional area, are joined end to end. A force applied to the combination stretches its total length by 1 cm. Find how much each wire stretches. (Y for copper = 1.2 × 10¹¹ N/m², for steel = 2.0 × 10¹¹ N/m²)
Hint
Answer
A uniform wire of density 8000 kg/m³ has a mass of 20 g and is 2.5 m long. It stretches by 1 mm when pulled by a force of 80 N. Find the Young’s modulus of the metal and the energy stored in the wire.
Answer
A wire 3.0 m long, of cross-sectional area 1.0 × 10⁻⁶ m², has a mass of 15 kg hung on it. What is the stress in the wire? If the Young’s modulus of its material is 2.0 × 10¹¹ N/m², what is the extension x? How much energy is stored in the stretched wire? (g = 9.8 m/s²)
Answer
A steel wire 2.00 m long must stretch by no more than 0.25 cm when a tensile force of 400 N is applied to each end. What is the least diameter it can have? (Y = 20 × 10¹⁰ N/m²)
Answer
A vertical brass rod of circular cross-section is loaded by placing a 5 kg weight on top of it. The rod is 50 cm long, its radius is 1 cm, and the Young’s modulus of brass is 3.5 × 10¹⁰ N/m². Find a. the contraction of the rod and b. the energy stored in it. (g = 9.8 m/s²)
Answer
In a materials testing laboratory, a wire made of a new alloy breaks when a tensile force of 90.8 N is applied to each end. If the wire’s diameter is 1.84 mm, what is the breaking stress of the alloy?
Answer
A metal rod 4.00 m long, of cross-sectional area 0.50 cm², stretches by 0.20 cm under a tension of 5000 N. What is the Young’s modulus of the metal?
Answer
A sample of oil of initial volume 600 cm³ is put under an extra pressure of 3.6 × 10⁶ Pa, and its volume decreases by 0.45 cm³. What is the bulk modulus of the oil? Its compressibility?
Answer
Printable PDFs
- The unit as a book (A5) 34 pages Answers as an A4 booklet, 9 sheets
- Study notes 2 pages
- Worksheet 4 pages Answer key
- Harder practice questions 2 pages Answer key
Quiz yourself: Force, Motion and Machines, Grades 5–12 →
Practice every question in the book, and keep track of the ones you miss →
A companion to your textbook, not a replacement for it: study from the book your school uses, and where the two differ, follow your teacher. Found a mistake? Please tell us.
