Skip to content

← Grade 11 Physics

Exam practice

Every question from the end of every unit, with hints and answers to open. After you check an answer, mark how you did, and come back to the ones you didn’t get.

17 questions

Unit 8 · Elasticity

Answer these questions

13.
  • a.State Hooke’s law.
  • b.Does Hooke’s law apply to all materials?
  • c.The elastic limit of steel is 8 × 10⁸ N/m² and its Young’s modulus is 2 × 10¹¹ N/m². What is the greatest elongation that can be given to a steel wire half a meter long without exceeding its elastic limit?
Answer
  • a.Hooke’s law: within the elastic limit, the extension of a body is directly proportional to the load (force) applied to it; equivalently, stress is directly proportional to strain.
  • b.No. It holds only up to the proportional limit, and not for every material even there. Metals obey it for small strains; brittle materials such as glass obey it until they break; but elastomers such as rubber don’t obey it at all: their stress–strain graph curves from the start, though they spring back.
  • c.At the elastic limit, strain = stress ÷ Y:

xL=8×1082×1011=4×10−3⇒x=4×10−3×0.5=2×10−3 m \frac{x}{L} = \frac{8 \times 10^8}{2 \times 10^{11}} = 4 \times 10^{-3} \quad\Rightarrow\quad x = 4 \times 10^{-3} \times 0.5 = 2 \times 10^{-3} \text{ m}
The greatest elongation is 2 mm.

14.
  • a.Name the three moduli of elasticity.
  • b.Which kind of elasticity does water have?
  • c.A steel guitar string 80 cm long and 1.0 mm in diameter is tightened to a tension of 2000 N by turning a screw. How far is the string stretched? (Y for steel = 2.0 × 10¹¹ N/m²)
Answer
  • a.Young’s modulus (for a change in length), bulk modulus (for a change in volume) and modulus of rigidity or shear modulus (for a change in shape).
  • b.Only volume (bulk) elasticity. Water resists being compressed, so it has a bulk modulus (2.2 × 10⁹ N/m²), but it can’t hold a shearing stress or a length of its own, so it has no modulus of rigidity and no Young’s modulus.
  • c.A=πd24=π×(1.0×10−3)24=7.85×10−7 A = \dfrac{\pi d^2}{4} = \dfrac{\pi \times (1.0 \times 10^{-3})^2}{4} = 7.85 \times 10^{-7} m².

x=FLAY=2000×0.807.85×10−7×2.0×1011=16001.57×105=1.02×10−2 m x = \frac{FL}{AY} = \frac{2000 \times 0.80}{7.85 \times 10^{-7} \times 2.0 \times 10^{11}} = \frac{1600}{1.57 \times 10^5} = 1.02 \times 10^{-2} \text{ m}
About 1.0 cm. (The stress, 2.5 × 10⁹ N/m², is about as much as the strongest piano wire can take: a real guitar string is tightened to only about 100 N.)

15.
  • a.What is meant by Poisson’s ratio?
  • b.Define elastic after-effect.
  • c.Find the increase in energy of a brass bar 0.5 m long, of cross-sectional area 1 × 10⁻⁴ m², when it is compressed along its length by a load of 5 kg. (Y for brass = 1.0 × 10¹¹ N/m², g = 10 m/s²)
Answer
  • a.When a wire is stretched (or a rod compressed), its width changes as well as its length. Within the elastic limit, the ratio of the lateral strain (the fractional change in diameter) to the longitudinal strain (the fractional change in length) is a constant for the material, Poisson’s ratio σ: σ=ΔD/DΔL/L \sigma = \dfrac{\Delta D/D}{\Delta L/L} . It has no unit.
  • b.Elastic after-effect is the delay with which a body regains its original shape and size after the deforming force has been removed.
  • c.F=mg=5×10=50 F = mg = 5 \times 10 = 50 N.

Compression: x=FLAY=50×0.51×10−4×1.0×1011=25107=2.5×10−6 x = \dfrac{FL}{AY} = \dfrac{50 \times 0.5}{1 \times 10^{-4} \times 1.0 \times 10^{11}} = \dfrac{25}{10^7} = 2.5 \times 10^{-6} m.
Energy stored: E=12Fx=12×50×2.5×10−6=6.25×10−5 E = \tfrac{1}{2}Fx = \tfrac{1}{2} \times 50 \times 2.5 \times 10^{-6} = 6.25 \times 10^{-5} J.

16.
  • a.What is elastic potential energy? Derive an expression for the energy stored in a stretched wire.
  • b.A uniform rod of a material with Poisson’s ratio 0.2 is given a longitudinal strain of 4 × 10⁻³. Find the percentage change in its volume.
  • c.A copper wire of cross-sectional area 0.01 cm² is under a tension of 25 N. Find the decrease in its cross-sectional area. (Y for copper = 1.1 × 10¹¹ N/m², σ = 0.32)
Hint

b. ΔVV=ε(1−2σ) \dfrac{\Delta V}{V} = \varepsilon(1 - 2\sigma) . c. The area is πr2 \pi r^2 , so its fractional decrease is twice the lateral strain.

Answer

a. Elastic potential energy is the energy stored in a body by deforming it within its elastic limit: the work done against its restoring force, given back when it returns to its shape.
Derivation (Section 8.5): a wire of length L and area A, fixed at its top, is stretched slowly. At extension x′ the force is F=YALx′ F = \dfrac{YA}{L}x' (from Y = (F/A)/(x′/L)). For a further small extension dx′ the work is dW=YALx′ dx′ dW = \dfrac{YA}{L}x'\,dx' . Integrating from 0 to the final extension x:
W=∫0xYALx′ dx′=12YALx2 W = \int_0^x \frac{YA}{L}x'\,dx' = \frac{1}{2}\frac{YA}{L}x^2
Since the final force is F=YALx F = \dfrac{YA}{L}x , W=12Fx W = \tfrac{1}{2}Fx . So the elastic PE = ½Fx = ½(YA/L)x², and per unit volume, ½ stress × strain.

  • b.ΔVV=ε(1−2σ)=4×10−3×(1−0.4)=2.4×10−3 \dfrac{\Delta V}{V} = \varepsilon(1 - 2\sigma) = 4 \times 10^{-3} \times (1 - 0.4) = 2.4 \times 10^{-3} , an increase of 0.24% (if the rod is stretched; a decrease if it is compressed).
  • c.A=0.01 cm2=1×10−6 A = 0.01 \text{ cm}^2 = 1 \times 10^{-6} m².

Longitudinal strain: FAY=251×10−6×1.1×1011=2.27×10−4 \dfrac{F}{AY} = \dfrac{25}{1 \times 10^{-6} \times 1.1 \times 10^{11}} = 2.27 \times 10^{-4} .
Lateral strain: Δrr=σ×2.27×10−4=0.32×2.27×10−4=7.27×10−5 \dfrac{\Delta r}{r} = \sigma \times 2.27 \times 10^{-4} = 0.32 \times 2.27 \times 10^{-4} = 7.27 \times 10^{-5} .
Since A=πr2 A = \pi r^2 , ΔAA=2Δrr=1.45×10−4 \dfrac{\Delta A}{A} = 2\dfrac{\Delta r}{r} = 1.45 \times 10^{-4} , so
ΔA=1.45×10−4×1×10−6=1.45×10−10 m2 \Delta A = 1.45 \times 10^{-4} \times 1 \times 10^{-6} = 1.45 \times 10^{-10} \text{ m}^2

17.
  • a.Discuss the different moduli of elasticity.
  • b.What force would be needed to stretch a steel wire of cross-sectional area 1 × 10⁻⁴ m² to double its length, if Hooke’s law held that far? (Y for steel = 2.0 × 10¹¹ N/m²)
  • c.A steel wire and a copper wire of equal cross-sectional area are joined end to end. When the combination is under tension, the two wires stretch by equal amounts. Find the ratio of the length of the steel wire to that of the copper wire. (Y for steel = 2.0 × 10¹¹ N/m², for copper 1.1 × 10¹¹ N/m²)
Answer

a. Within the elastic limit, each kind of stress and the strain it causes have a constant ratio, a modulus of elasticity:

  • Young’s modulus, Y=normal stresslongitudinal strain=FLAx Y = \dfrac{\text{normal stress}}{\text{longitudinal strain}} = \dfrac{FL}{Ax} : resistance to a change in length; for solids only.
  • Bulk modulus, B=normal stressvolumetric strain=P−ΔV/V B = \dfrac{\text{normal stress}}{\text{volumetric strain}} = \dfrac{P}{-\Delta V/V} : resistance to a change in volume; solids, liquids and gases all have one. Its reciprocal is the compressibility.
  • Modulus of rigidity, η=tangential stressshear strain=F/Aϕ \eta = \dfrac{\text{tangential stress}}{\text{shear strain}} = \dfrac{F/A}{\phi} : resistance to a change in shape; for solids only.

All three are in N/m² (Pa).
b. Doubling the length means an extension x = L, a strain of 1:
F=YAxL=YA×1=2.0×1011×1×10−4=2.0×107 N F = \frac{YAx}{L} = YA \times 1 = 2.0 \times 10^{11} \times 1 \times 10^{-4} = 2.0 \times 10^7 \text{ N}
So the Young’s modulus is the stress that would double a wire’s length, if Hooke’s law held that far. It doesn’t: real steel yields at a strain of a fraction of one percent and breaks long before its length doubles.
c. The tension F is the same in both (they are in a line), and so are the areas. Equal extensions:
FLsAYs=FLcAYc⇒LsLc=YsYc=2.0×10111.1×1011=2011 \frac{FL_s}{AY_s} = \frac{FL_c}{AY_c} \quad\Rightarrow\quad \frac{L_s}{L_c} = \frac{Y_s}{Y_c} = \frac{2.0 \times 10^{11}}{1.1 \times 10^{11}} = \frac{20}{11}
The steel wire must be the longer, in the ratio 20 : 11.

18.
  • a.What are the elastic limit and the breaking stress?
  • b.Define elastic hysteresis.
  • c.A sample of fishing line is 1.0 m long, with a circular cross-section of radius 0.25 mm. When a weight is hung on it, it stretches by 50 mm and the stress is 2.0 × 10⁸ Pa. Find i. its cross-sectional area, ii. the weight hung on it, iii. the strain, and iv. its Young’s modulus.
Answer
  • a.The elastic limit is the greatest stress a body can take and still return completely to its original shape and size when the stress is removed. The breaking stress is the stress at which it breaks; the greatest stress it can bear (the ultimate tensile stress, point D of the stress–strain curve) is often given as the breaking stress of the material.
  • b.Elastic hysteresis is the lag of strain behind stress when a body is loaded and then unloaded: the stress–strain curve on unloading lies below the curve on loading, making a closed loop whose area is the energy turned into heat per unit volume in each cycle.
  • c.i. A=πr2=π×(0.25×10−3)2=1.96×10−7≈2.0×10−7 A = \pi r^2 = \pi \times (0.25 \times 10^{-3})^2 = 1.96 \times 10^{-7} \approx 2.0 \times 10^{-7} m².
  • ii.W=stress×A=2.0×108×1.96×10−7=39 W = \text{stress} \times A = 2.0 \times 10^8 \times 1.96 \times 10^{-7} = 39 N.
  • iii.Strain =xL=0.0501.0=0.05 = \dfrac{x}{L} = \dfrac{0.050}{1.0} = 0.05 .
  • iv.Y=stressstrain=2.0×1080.05=4.0×109 Y = \dfrac{\text{stress}}{\text{strain}} = \dfrac{2.0 \times 10^8}{0.05} = 4.0 \times 10^9 Pa. (Nylon’s modulus is about a fiftieth of steel’s, which is why a fishing line stretches so much.)

Numerical problems

19.

Young’s modulus for steel is 2.0 × 10¹¹ N/m². Find the work done in stretching a steel wire 100 cm long, of cross-sectional area 0.030 cm², when a load of 100 N is slowly applied, without the elastic limit being reached.

Answer

L=1.00 L = 1.00 m, A=0.030 cm2=3.0×10−6 A = 0.030 \text{ cm}^2 = 3.0 \times 10^{-6} m², F = 100 N.
x=FLAY=100×1.003.0×10−6×2.0×1011=1.67×10−4 m x = \frac{FL}{AY} = \frac{100 \times 1.00}{3.0 \times 10^{-6} \times 2.0 \times 10^{11}} = 1.67 \times 10^{-4} \text{ m}
W=12Fx=12×100×1.67×10−4=8.3×10−3 J W = \tfrac{1}{2}Fx = \tfrac{1}{2} \times 100 \times 1.67 \times 10^{-4} = 8.3 \times 10^{-3} \text{ J}

20.

A uniform steel wire of density 7800 kg/m³ has a mass of 16 g and is 2.50 m long. It stretches by 1.2 mm when pulled by a force of 80 N. Find a. the Young’s modulus of the steel and b. the energy stored in the wire.

Hint

The wire’s volume is its mass ÷ density, and its area is its volume ÷ length.

Answer

Volume: V=mρ=0.0167800=2.05×10−6 V = \dfrac{m}{\rho} = \dfrac{0.016}{7800} = 2.05 \times 10^{-6} m³. Area: A=VL=2.05×10−62.50=8.21×10−7 A = \dfrac{V}{L} = \dfrac{2.05 \times 10^{-6}}{2.50} = 8.21 \times 10^{-7} m².

  • a.Y=FLAx=80×2.508.21×10−7×1.2×10−3=2.0×1011 Y = \dfrac{FL}{Ax} = \dfrac{80 \times 2.50}{8.21 \times 10^{-7} \times 1.2 \times 10^{-3}} = 2.0 \times 10^{11} N/m².
  • b.E=12Fx=12×80×1.2×10−3=4.8×10−2 E = \tfrac{1}{2}Fx = \tfrac{1}{2} \times 80 \times 1.2 \times 10^{-3} = 4.8 \times 10^{-2} J.
21.

The rubber cord of a catapult has a cross-sectional area of 1.0 mm² and an unstretched length of 10.0 cm. It is stretched to 12.0 cm and then released to throw a stone of mass 5.0 g. From energy considerations, or otherwise, find the speed with which the stone is thrown. (Y for rubber = 5.0 × 10⁸ N/m²)

Answer

x=2.0 x = 2.0 cm = 0.020 m, L=0.100 L = 0.100 m, A=1.0×10−6 A = 1.0 \times 10^{-6} m².
Energy stored:
E=12 YAL x2=12×5.0×108×1.0×10−60.100×(0.020)2=1.0 J E = \frac{1}{2}\,\frac{YA}{L}\,x^2 = \frac{1}{2} \times \frac{5.0 \times 10^8 \times 1.0 \times 10^{-6}}{0.100} \times (0.020)^2 = 1.0 \text{ J}
All of it becomes the stone’s kinetic energy:
12×0.0050×v2=1.0⇒v=400=20 m/s \tfrac{1}{2} \times 0.0050 \times v^2 = 1.0 \quad\Rightarrow\quad v = \sqrt{400} = \textbf{20 m/s}
(In practice a little is lost to the cord’s hysteresis and to its own motion, so the stone goes a little slower.)

22.

A copper wire 1 m long and a steel wire 2 m long, of the same cross-sectional area, are joined end to end. A force applied to the combination stretches its total length by 1 cm. Find how much each wire stretches. (Y for copper = 1.2 × 10¹¹ N/m², for steel = 2.0 × 10¹¹ N/m²)

Hint

The same force acts in both wires. Write each extension as FL/(AY) and compare them.

Answer

With the same F and A, x∝LY x \propto \dfrac{L}{Y} :
xcxs=LcYc⋅YsLs=11.2×2.02=11.2=56 \frac{x_c}{x_s} = \frac{L_c}{Y_c} \cdot \frac{Y_s}{L_s} = \frac{1}{1.2} \times \frac{2.0}{2} = \frac{1}{1.2} = \frac{5}{6}
So xc=56xs x_c = \tfrac{5}{6}x_s , and xc+xs=1 x_c + x_s = 1 cm:
116xs=1 cm⇒xs=0.545 cm,xc=0.455 cm \tfrac{11}{6}x_s = 1 \text{ cm} \quad\Rightarrow\quad x_s = 0.545 \text{ cm}, \quad x_c = 0.455 \text{ cm}
The copper wire stretches by about 0.0045 m and the steel wire by about 0.0055 m.

23.

A uniform wire of density 8000 kg/m³ has a mass of 20 g and is 2.5 m long. It stretches by 1 mm when pulled by a force of 80 N. Find the Young’s modulus of the metal and the energy stored in the wire.

Answer

V=0.0208000=2.5×10−6 V = \dfrac{0.020}{8000} = 2.5 \times 10^{-6} m³, so A=VL=2.5×10−62.5=1.0×10−6 A = \dfrac{V}{L} = \dfrac{2.5 \times 10^{-6}}{2.5} = 1.0 \times 10^{-6} m².
Y=FLAx=80×2.51.0×10−6×1.0×10−3=2.0×1011 N/m2 Y = \frac{FL}{Ax} = \frac{80 \times 2.5}{1.0 \times 10^{-6} \times 1.0 \times 10^{-3}} = 2.0 \times 10^{11} \text{ N/m}^2
E=12Fx=12×80×1.0×10−3=4.0×10−2 J E = \tfrac{1}{2}Fx = \tfrac{1}{2} \times 80 \times 1.0 \times 10^{-3} = 4.0 \times 10^{-2} \text{ J}

24.

A wire 3.0 m long, of cross-sectional area 1.0 × 10⁻⁶ m², has a mass of 15 kg hung on it. What is the stress in the wire? If the Young’s modulus of its material is 2.0 × 10¹¹ N/m², what is the extension x? How much energy is stored in the stretched wire? (g = 9.8 m/s²)

Answer

F=15×9.8=147 F = 15 \times 9.8 = 147 N.
Stress: FA=1471.0×10−6=1.47×108 \dfrac{F}{A} = \dfrac{147}{1.0 \times 10^{-6}} = 1.47 \times 10^8 N/m².
Extension: x=stress×LY=1.47×108×3.02.0×1011=2.2×10−3 x = \dfrac{\text{stress} \times L}{Y} = \dfrac{1.47 \times 10^8 \times 3.0}{2.0 \times 10^{11}} = 2.2 \times 10^{-3} m.
Energy: E=12Fx=12×147×2.205×10−3=0.162 E = \tfrac{1}{2}Fx = \tfrac{1}{2} \times 147 \times 2.205 \times 10^{-3} = 0.162 J.

25.

A steel wire 2.00 m long must stretch by no more than 0.25 cm when a tensile force of 400 N is applied to each end. What is the least diameter it can have? (Y = 20 × 10¹⁰ N/m²)

Answer

From x=FLAY x = \dfrac{FL}{AY} , the least area is
A=FLYx=400×2.002.0×1011×0.0025=1.6×10−6 m2 A = \frac{FL}{Yx} = \frac{400 \times 2.00}{2.0 \times 10^{11} \times 0.0025} = 1.6 \times 10^{-6} \text{ m}^2
d=4Aπ=4×1.6×10−6π=1.43×10−3 m d = \sqrt{\frac{4A}{\pi}} = \sqrt{\frac{4 \times 1.6 \times 10^{-6}}{\pi}} = 1.43 \times 10^{-3} \text{ m}
At least 1.43 mm.

26.

A vertical brass rod of circular cross-section is loaded by placing a 5 kg weight on top of it. The rod is 50 cm long, its radius is 1 cm, and the Young’s modulus of brass is 3.5 × 10¹⁰ N/m². Find a. the contraction of the rod and b. the energy stored in it. (g = 9.8 m/s²)

Answer

F=5×9.8=49 F = 5 \times 9.8 = 49 N; A=π×(0.01)2=3.14×10−4 A = \pi \times (0.01)^2 = 3.14 \times 10^{-4} m²; L=0.50 L = 0.50 m.

  • a.x=FLAY=49×0.503.14×10−4×3.5×1010=24.51.10×107=2.2×10−6 x = \dfrac{FL}{AY} = \dfrac{49 \times 0.50}{3.14 \times 10^{-4} \times 3.5 \times 10^{10}} = \dfrac{24.5}{1.10 \times 10^7} = 2.2 \times 10^{-6} m.
  • b.E=12Fx=12×49×2.23×10−6=5.5×10−5 E = \tfrac{1}{2}Fx = \tfrac{1}{2} \times 49 \times 2.23 \times 10^{-6} = 5.5 \times 10^{-5} J.

(With g = 10 m/s², 2.27 × 10⁻⁶ m and 5.7 × 10⁻⁵ J.)

27.

In a materials testing laboratory, a wire made of a new alloy breaks when a tensile force of 90.8 N is applied to each end. If the wire’s diameter is 1.84 mm, what is the breaking stress of the alloy?

Answer

A=πd24=π×(1.84×10−3)24=2.66×10−6 A = \dfrac{\pi d^2}{4} = \dfrac{\pi \times (1.84 \times 10^{-3})^2}{4} = 2.66 \times 10^{-6} m².
breaking stress=FA=90.82.66×10−6=3.41×107 Pa \text{breaking stress} = \frac{F}{A} = \frac{90.8}{2.66 \times 10^{-6}} = 3.41 \times 10^7 \text{ Pa}

28.

A metal rod 4.00 m long, of cross-sectional area 0.50 cm², stretches by 0.20 cm under a tension of 5000 N. What is the Young’s modulus of the metal?

Answer

A=0.50 cm2=5.0×10−5 A = 0.50 \text{ cm}^2 = 5.0 \times 10^{-5} m²; x=2.0×10−3 x = 2.0 \times 10^{-3} m.
Y=FLAx=5000×4.005.0×10−5×2.0×10−3=20 0001.0×10−7=2.0×1011 N/m2 Y = \frac{FL}{Ax} = \frac{5000 \times 4.00}{5.0 \times 10^{-5} \times 2.0 \times 10^{-3}} = \frac{20\,000}{1.0 \times 10^{-7}} = 2.0 \times 10^{11} \text{ N/m}^2

29.

A sample of oil of initial volume 600 cm³ is put under an extra pressure of 3.6 × 10⁶ Pa, and its volume decreases by 0.45 cm³. What is the bulk modulus of the oil? Its compressibility?

Answer

Volumetric strain: 0.45600=7.5×10−4 \dfrac{0.45}{600} = 7.5 \times 10^{-4} .
B=P−ΔV/V=3.6×1067.5×10−4=4.8×109 Pa B = \frac{P}{-\Delta V/V} = \frac{3.6 \times 10^6}{7.5 \times 10^{-4}} = 4.8 \times 10^9 \text{ Pa}
K=1B=2.1×10−10 Pa−1 K = \frac{1}{B} = 2.1 \times 10^{-10} \text{ Pa}^{-1}