Exam practice
Every question from the end of every unit, with hints and answers to open. After you check an answer, mark how you did, and come back to the ones you didn’t get.
6 questions
Unit 23 · DC Circuits
Printable PDFs
- The unit as a book (A5) 27 pages Answers as an A4 booklet, 7 sheets
- Study notes 3 pages
- Worksheet 5 pages Answer key
- Harder practice questions 2 pages Answer key
Numerical problems
- a.The copper wire supplying the sockets in your house has a cross-sectional area of 2.5 mm². A hair dryer draws a current of 8.2 A. What is the mean drift velocity of the electrons in the wire? Take the number density of free electrons in copper as 8.49 × 10²⁸ m⁻³.
- b.A 1 molar solution of copper sulphate contains 6.02 × 10²⁶ Cu²⁺ ions per cubic meter. A beaker of this solution has two electrodes placed in it, through which a current of 30 mA is passed. What is the mean drift velocity of the copper ions? Take the cross-sectional area of the solution as 100 cm², and assume the copper ions carry all the current.
Hint
v = I/(nAq). Change mm² and cm² into m². A Cu²⁺ ion carries a charge of 2e.
Answer
a. m².
b. m², and q = 2e = 3.2 × 10⁻¹⁹ C.
about 0.06 mm an hour. (In fact the sulphate ions, moving the other way, carry part of the current, so the copper ions drift even more slowly.)
A tungsten lamp filament of diameter 0.046 mm carries a current of 0.50 A. What is the mean drift velocity of the electrons in the filament? Take the number density of free electrons in tungsten as 1.26 × 10²⁹ m⁻³.
Answer
The radius is 0.023 mm = 2.3 × 10⁻⁵ m, so m².
A copper wire of diameter 0.65 mm carries a current of 0.25 A. There are 8.5 × 10²⁸ charge carriers in each cubic meter of copper; the charge on each carrier (an electron) is 1.6 × 10⁻¹⁹ C. Calculate the drift speed of the charge carriers.
Answer
The radius is 0.325 mm = 3.25 × 10⁻⁴ m, so m².
about 0.055 mm/s.
- a.State what physical quantity is represented by each term in the equation I = nAvq.
- b.A semiconducting strip 6.0 mm wide and 0.50 mm thick carries a current of 10 mA along its length, as shown. If the value of n for the semiconducting material is 7.0 × 10²² m⁻³, show that the drift speed of the charge carriers, each of charge 1.6 × 10⁻¹⁹ C, is about 0.3 m/s.
Answer
- a.I: the current (A); n: the number density of charge carriers, the number per unit volume (m⁻³); A: the cross-sectional area of the conductor (m²); v: the mean drift velocity of the carriers (m/s); q: the charge on each carrier (C).
- b.The cross-section is m².
about 0.3 m/s, as stated: thousands of times faster than in copper, because the semiconductor has a million times fewer carriers.
The resistance of a light-dependent resistor (LDR) as a function of light intensity is shown in the graph below.
A manufacturer of light-sensitive switches wants to use this LDR to turn a set of garden lights on when the outdoor light intensity drops below 200 lux. Draw a potential divider that would let the garden lights’ circuit switch the lights on when its output p.d. falls to 2.5 V or below.
Hint
Read the LDR’s resistance at 200 lux. Which way round must the LDR and the fixed resistor be for the output to fall as it gets darker?
Answer
The question doesn’t give the supply, so take a 5.0 V supply (a common value for such circuits).
At 200 lux, the graph gives the LDR a resistance of about 350 kΩ.
Which way round. As it gets darker, the LDR’s resistance rises, so its share of the p.d. rises and the fixed resistor’s share falls. We want the output to fall as it gets darker, so the output is taken across the fixed resistor: the LDR goes between the supply’s + terminal and the output, the fixed resistor between the output and 0 V.
The fixed resistor. At exactly 200 lux the output must be 2.5 V, half of 5.0 V, so the two resistances must be equal: the fixed resistor R must be about 350 kΩ (or the nearest standard value, 360 kΩ).
Check. Brighter than 200 lux (say 400 lux, about 120 kΩ): V, above 2.5 V: lights off. Darker (100 lux, about 590 kΩ): V, below 2.5 V: lights on.
The figure below shows a circuit diagram. The current measured by the ammeter is 220 mA.
- a.Calculate the value of the resistance R.
- b.Describe how the total current in the circuit would change if the resistor R were disconnected from the circuit. Explain why the current would change in that way.
The textbook draws the two cells facing opposite ways. That gives 10.5 − 6 = 4.5 V and a total resistance of 4.5 ÷ 0.22 = 20.5 Ω, less than the 21.2 Ω of the resistors that are plainly in series, so R would have to be negative. So the book’s numbers don’t work; here the cells face the same way (16.5 V).
Hint
Find the total resistance from E/I. Subtract everything that is plainly in series; what is left is (150 + 45) Ω in parallel with R.
Answer
a. Total resistance. The cells together give 6 + 10.5 = 16.5 V, so
The part in series. 25 Ω and 50 Ω in parallel: Ω. With the 2.5 Ω and the 2 Ω: 2.5 + 16.7 + 2 = 21.2 Ω.
The parallel block. 75 − 21.2 = 53.8 Ω. It is (150 + 45) = 195 Ω in parallel with R:
b. Without R, the block is just 195 Ω, so the total resistance rises to 195 + 21.2 = 216 Ω, and the current decreases, to A = 76 mA. Removing a parallel branch removes one of the paths for the current, so the resistance of that part, and of the whole circuit, increases; with the same e.m.f., the current falls.
