Skip to content

← Grade 12 Physics

Exam practice

Every question from the end of every unit, with hints and answers to open. After you check an answer, mark how you did, and come back to the ones you didn’t get.

4 questions

Unit 22 · Semiconductor Devices

Answer these questions

11.
  • a.Explain the formation of the potential barrier and the depletion layer in a p–n junction.
  • b.Explain the forward and reverse characteristics of a p–n junction diode.
Hint

a. Diffusion, recombination, the fixed ions left behind, and the field they make. b. Draw the circuit and the graph, and describe each part of the curve.

Answer
  • a.In the p region the majority carriers are holes, in the n region free electrons. Because of the difference in their concentrations, holes diffuse from the p side into the n side and electrons from the n side into the p side, where they recombine. So a thin region on each side of the junction (about 0.01–1 µm) is left with no free carriers: the depletion layer. It contains only the fixed ions: negative acceptor ions on the p side, positive donor ions on the n side. These charges set up an electric field from the n side to the p side, which opposes further diffusion; diffusion stops when the two balance. The potential difference across the depletion layer is the potential barrier: about 0.7 V for silicon and 0.3 V for germanium.
  • b.Forward characteristic (p side to +; circuit Figure 22.4): as the forward voltage rises from zero, almost no current flows until the barrier is overcome, at the knee voltage (0.7 V for Si, 0.3 V for Ge). Beyond the knee the current (in mA) rises very steeply, since the depletion layer is thin and the resistance low. Too large a current overheats and destroys the diode.

Reverse characteristic (p side to −, with a microammeter; Figure 22.6): only a tiny reverse current of minority carriers flows (µA), almost constant as the voltage rises, since the depletion layer is wide and the resistance very high. At the breakdown voltage VB V_B the current suddenly rises sharply, as carriers accelerated by the strong field knock more electrons out of their bonds (avalanche). The graph is Figure 22.5.

12.
  • a.What is a junction diode? Explain a full-wave rectifier using two diodes.
  • b.What will happen if one of the diodes is damaged?
  • c.The output of a full-wave rectifier is pulsating d.c. Which device can be used to get a constant output voltage? Draw its symbol and its characteristic.
Hint

a. The center-tapped transformer. b. A diode can fail open (no current) or short (always conducting): think through both.

Answer

a. A junction diode is a p–n junction with a lead to each side: it lets current through when forward biased and practically none when reverse biased.
Full-wave rectifier with two diodes (Figure 22.10): the secondary of a center-tapped transformer has ends S₁ and S₂; S₁ goes through diode D₁ and S₂ through D₂ to one end (X) of the load RL R_L ; the center tap goes to the other end (Y). In one half cycle S₁ is positive with respect to the center tap: D₁ conducts, D₂ is reverse biased, and current flows S₁ → D₁ → X → RL R_L → Y → center tap. In the next half cycle S₂ is positive: D₂ conducts, D₁ is off, and current flows S₂ → D₂ → X → RL R_L → Y. In both halves the current through RL R_L flows from X to Y, so both halves of the a.c. give output in the same direction (Figure 22.12).

  • b.If one diode fails open (it no longer conducts), the circuit works on only one half of each cycle: it becomes a half-wave rectifier, with half the average output and a gap every other half cycle. If a diode fails short-circuited, then in the half cycle when it should be blocking, it joins its end of the secondary straight to the other end through the working diode, short-circuiting the transformer: a very large current flows, which can damage the transformer and the other diode (or blow a fuse).
  • c.A Zener diode (after a filter capacitor), connected reverse biased across the load with a series resistor (Figure 22.8), gives a constant output voltage VZ V_Z . Its symbol and characteristic are Figure 22.3 and Figure 22.7: forward like an ordinary diode; reverse, almost no current until VZ V_Z , then a nearly vertical rise at constant voltage.
13.
  • a.What are logic gates? Give the truth table of a two-input NAND gate, with its symbol.
  • b.Explain why the NAND gate is called a universal gate.
Answer

a. Logic gates are digital circuits with one or more inputs and one output, each either 1 (high voltage) or 0 (low voltage), whose output follows a definite logical rule of the inputs (OR, AND, NOT, and combinations). They are the building blocks of computers and other digital systems.
The NAND gate is an AND gate followed by a NOT; its symbol is the AND symbol with a small circle at its output (Figure 22.20), and Y=A⋅B‾ Y = \overline{A \cdot B} :

A B Y = A⋅B‾ \overline{A \cdot B}
0 0 1
0 1 1
1 0 1
1 1 0

b. The NAND gate is universal because NAND gates alone can make the three basic gates, and so any logic circuit (Figure 22.21):

  • NOT: one NAND with its inputs joined, A⋅A‾=Aˉ \overline{A \cdot A} = \bar{A} ;
  • AND: a NAND followed by a NAND-NOT, A⋅B‾‾=A⋅B \overline{\overline{A \cdot B}} = A \cdot B ;
  • OR: Aˉ \bar{A} and Bˉ \bar{B} from two NAND-NOTs into a third NAND, Aˉ⋅Bˉ‾=A+B \overline{\bar{A} \cdot \bar{B}} = A + B .
14.
  • a.Draw a circuit diagram to realize an AND gate from NOR gates, with its truth table.
  • b.Which gate will you get if you connect a NOT gate at the output of the circuit of part a?
  • c.Show, using a truth table, that the circuit given below acts as an OR gate.
ABNANDNANDNANDABY
Figure 22.31 For question 14 c: A and B each go to both inputs of a NAND gate; the two outputs go to a third NAND gate.
Hint

a. Invert each input first. c. Work out Aˉ \bar{A} and Bˉ \bar{B} , then the last NAND.

Answer

a. Two NOR gates with their inputs joined give Aˉ \bar{A} and Bˉ \bar{B} ; a third NOR gives
Y=Aˉ+Bˉ‾=A⋅B(De Morgan) Y = \overline{\bar{A} + \bar{B}} = A \cdot B \quad\text{(De Morgan)}

ABNORNORNORABY
Figure 22.32 An AND gate made of three NOR gates.
A B Aˉ \bar{A} Bˉ \bar{B} Aˉ+Bˉ \bar{A} + \bar{B} Y
0 0 1 1 1 0
0 1 1 0 1 0
1 0 0 1 1 0
1 1 0 0 0 1
  • b.A NOT gate after an AND gives A⋅B‾ \overline{A \cdot B} : a NAND gate.
  • c.The first NAND gate, with both inputs A, gives Aˉ \bar{A} ; the second gives Bˉ \bar{B} ; the third gives Y=Aˉ⋅Bˉ‾ Y = \overline{\bar{A} \cdot \bar{B}} .
A B Aˉ \bar{A} Bˉ \bar{B} Aˉ⋅Bˉ \bar{A} \cdot \bar{B} Y
0 0 1 1 1 0
0 1 1 0 0 1
1 0 0 1 0 1
1 1 0 0 0 1

The output column, 0 1 1 1, is exactly that of A + B: the circuit acts as an OR gate.