Exam practice
Every question from the end of every unit, with hints and answers to open. After you check an answer, mark how you did, and come back to the ones you didn’t get.
10 questions
Unit 11 · Quantity of Heat
Printable PDFs
- The unit as a book (A5) 23 pages Answers as an A4 booklet, 6 sheets
- Study notes 3 pages
- Worksheet 5 pages Answer key
- Harder practice questions 2 pages Answer key
Answer these questions
- a.What does the statement “the specific heat capacity of water is 4200 J/(kg K)” mean?
- b.Why are raw peanuts fried in a sand bath?
- c.An 80 kg man with flu has a fever of 39.0 °C instead of his normal 37.0 °C. Taking the human body as mostly water, how much heat raised his temperature by this amount? (Water 4200 J/(kg K).)
Answer
- a.4200 J of heat is needed to raise the temperature of 1 kg of water by 1 K (1 °C); and 1 kg of water gives out 4200 J when it cools by 1 K.
- b.Sand has a low specific heat capacity (about 800 J/(kg K)), so it heats up quickly to a high temperature on the fire; and it surrounds each peanut, passing heat to it evenly from every side, so the nuts roast through without burning on the hot pan. Sand also can’t boil away like water or soak in like oil, and it falls off the nuts when sieved.
- c. J ≈ 6.7 × 10⁵ J.
- a.State and explain Newton’s law of cooling.
- b.A body at 100 °C cools to 60 °C in 5 minutes and to 40 °C in 10 minutes. What will its temperature be at the end of 15 minutes?
Hint
b. First find the temperature of the surroundings. Under Newton’s law, the excess over the surroundings falls by the same fraction in each 5 minutes.
Answer
- a.The rate at which a body loses heat is proportional to the difference between its temperature and its surroundings’ temperature: . So a body cools fast when it is much hotter than its surroundings, and more and more slowly as it nears their temperature. With , integrating gives : a straight line on a graph of against . It holds for small temperature differences, with the surroundings at a constant temperature.
- b.Let the surroundings be at . In equal times (5 min each), the excess temperature falls by the same fraction:
°C.
The excess goes 80 → 40 → 20: it halves every 5 min. After 15 min it is 10 °C, so the temperature is 30 °C.
(The averaging method of the worked example gives the same: and give °C and per minute; then gives °C.)
The graph above shows the temperature of 1.00 g of ice, initially at −30 °C, as energy is added until it is steam at 120 °C.
- a.What do the parts B and D show?
- b.Are the slopes of the parts A, C and E equal or different? Why?
- c.Why is part D longer than part B?
- d.What are the temperatures of the parts B and D called?
- e.From the graph, calculate the specific latent heat of fusion of ice and the specific latent heat of vaporization of water.
Answer
- a.B: the ice melting at 0 °C (ice and water together, the temperature not changing). D: the water boiling at 100 °C (water and steam together).
- b.Different. Each slope is the rise in temperature per joule, : with the same mass, it depends on the specific heat capacity, which is different for ice (A), water (C) and steam (E). Water’s is the largest, so C is the least steep.
- c.D is the latent heat of vaporization, B the latent heat of fusion. Turning water into steam pulls the molecules right apart and pushes back the atmosphere as it expands about 1700 times, so it takes far more energy (nearly 7 times) than melting ice, which only loosens the molecules.
- d.B is at the melting point (freezing point) of ice, 0 °C; D at the boiling point of water, 100 °C (at 1 atm).
- e.Part B: J melts 1.00 g, so 3.33 × 10⁵ J/kg.
Part D: J boils 1.00 g, so 2.27 × 10⁶ J/kg.
- a.To raise the temperature of an object, must you add heat to it? If you add heat to an object, must its temperature rise? Explain.
- b.A nail driven into a board gets warmer. Ankit strikes an 8.00 g aluminium nail ten times with a 1.80 kg hammer moving at 7.80 m/s. If 60% of the hammer’s kinetic energy turns into heat that stays in the nail, by how much does the nail’s temperature rise? (Aluminium 910 J/(kg K).)
Answer
- a.No to both. A temperature can be raised without heat, by doing work on the object: rubbing, hammering, compressing a gas, stirring or shaking a liquid. And heat added need not raise the temperature: while the object is melting or boiling, the heat goes in as latent heat and the temperature stays constant.
- b.Kinetic energy of one blow: J. Ten blows, 60% into the nail: J.
- a.A beaker of water at room temperature is placed in a closed chamber, and the air is slowly pumped out. When the pressure is low enough, the water begins to boil, but its temperature doesn’t rise; in fact it falls slightly. Why?
- b.1 g of steam at 100 °C and 5 g of ice at 0 °C are mixed. What is the final result? (Water 4200 J/(kg K); latent heat of fusion of ice 3.36 × 10⁵ J/kg; of vaporization of water 2.26 × 10⁶ J/kg.)
Answer
- a.Lowering the pressure lowers the boiling point, until it falls to room temperature and the water boils. Boiling needs latent heat of vaporization, and no flame supplies it: it comes from the water itself, so the water cools. As it cools, it would stop boiling, unless the pressure is lowered further. (Keep pumping, and the water can even freeze while it boils.)
- b.Check first: 1 g of steam condensing and cooling to 0 °C gives at most J; 5 g of ice needs J to melt. So all the ice melts, and the final temperature θ is above 0 °C.
Heat lost by the steam: J.
Heat gained by the ice: J.
°C.
The result: 6 g of water at about 40 °C.
- a.Explain the role of latent heat in a change of phase, and how it affects the temperature during the change.
- b.Design an experiment to find the energy needed to change 1 kg of ice into water at 0 °C. Give the steps, the materials and equipment, the variables to keep the same, and the measurements to take.
- c.Suggest how the results might be interpreted, and what they mean for materials science.
- d.Discuss how pressure affects the melting point of substances.
Answer
- a.During a change of phase, the heat supplied (or removed) is the latent heat. It changes the potential energy of the particles (pulling them apart on melting or boiling, letting them come together on freezing or condensing), not their average kinetic energy, so the temperature stays constant until the change is complete, whatever the rate of heating. That is why a heating curve has flat parts, why ice keeps a drink at 0 °C until it has melted, and why boiling water stays at its boiling point however high the flame.
- b.Method of mixtures (11.13). Materials: a copper calorimeter with stirrer, its insulating box, a thermometer reading to 0.1 °C, a balance, warm water, melting ice, blotting paper. Steps: weigh the calorimeter (); two-thirds fill it with water about 10 °C above room temperature and weigh again (); note the temperature ; add dried pieces of melting ice, stirring until all has melted, and note the lowest temperature ; weigh again (). Keep the same: the insulation, the stirring, no water carried in with the ice (blot it dry), ice at 0 °C (melting). Calculate ; the energy for 1 kg is kg, about 3.3 × 10⁵ J. (Another way: melt ice with an electric heater of known power in a funnel, collect the melted water, and subtract the melting caused by the room, measured with an identical funnel and no heater: .)
- c.A result near 3.34 × 10⁵ J/kg shows the method works; a lower result usually means heat came in from the room or water came in with the ice, a higher one that heat was lost. For materials science: a large latent heat means a material stores a lot of energy at one fixed temperature. Such phase-change materials (ice, wax, salt hydrates) are used to keep vaccines and food cold during transport, to store solar heat, and to keep buildings and electronics at a steady temperature.
- d.A substance that expands on melting (wax, lead, most substances) has its melting point raised by pressure: pressure resists the expansion. A substance that contracts on melting (ice, cast iron, bismuth) has its melting point lowered by pressure. The effect is small: for ice, about 0.0075 °C per atmosphere. It explains regelation, and why the fusion curve of water on a phase diagram leans to the left.
Numerical problems
A 1 kW immersion heater heats 1 liter of water in a kettle for 5 minutes, and the temperature rises by 60 °C. Find the heat capacity of the kettle. (Water 4200 J/(kg K).)
Answer
Heat supplied: J.
This warms the water (1 kg) and the kettle (heat capacity ) by 60 °C: , so , and 800 J/K (0.8 × 10³ J/K).
A lead bullet hits a target at 500 m/s. Find the rise in its temperature, if 40% of the heat produced goes into heating the bullet. (Lead 126 J/(kg K).)
Answer
The mass cancels. (Lead melts at 327 °C, so a real bullet hitting at this speed would partly melt: some of this heat would go into melting it rather than raising its temperature.)
You are designing an electronic circuit element made of 23 mg of silicon. The current through it adds energy at 7.4 × 10⁻³ J/s. If the design lets no heat out of the element, how fast does its temperature rise? (Silicon 705 J/(kg K).)
Answer
In each second, J, so
Nearly half a degree a second: in a few minutes it would be ruined. That is why chips need heat sinks and fans.
Yangchen, a geologist working in the field, drinks her morning coffee from an aluminium cup of mass 0.120 kg at 20.0 °C. She pours in 0.300 kg of coffee at 70.0 °C. What is the final temperature, once the cup and coffee are at the same temperature? (Take coffee’s specific heat capacity as water’s, 4200 J/(kg K); aluminium 910 J/(kg K); no heat lost to the surroundings.)
Answer
Heat gained by the cup = heat lost by the coffee:
66.0 °C.
The cup takes only 4 °C off the coffee: its heat capacity, 109 J/K, is tiny beside the coffee’s, 1260 J/K.
