Exam practice
Every question from the end of every unit, with hints and answers to open. After you check an answer, mark how you did, and come back to the ones you didn’t get.
19 questions
Unit 1 · Volumetric Analysis
Printable PDFs
- Study notes 3 pages
- Worksheet 4 pages Answer key
Answer these questions
Define, and tell the difference between:
- a.molarity and normality
- b.ppm and ppb
- c.molarity and molality
- d.number of moles and number of gram equivalents
- e.a primary and a secondary standard substance
- f.an acid–base titration and a redox titration
Answer
- a.Molarity is the moles of solute in 1 L of solution; normality is the gram equivalents of solute in 1 L of solution. N = M × n, so they are equal only when n = 1 (HCl, NaOH, NaCl); 1 M H₂SO₄ is 2 N.
- b.ppm is parts of solute in a million (10⁶) parts of solution; ppb is parts in a billion (10⁹). 1 ppm = 1000 ppb; in water, 1 ppm ≈ 1 mg/L and 1 ppb ≈ 1 µg/L.
- c.Molarity is moles of solute per liter of solution, and changes with temperature; molality is moles of solute per kilogram of solvent, and doesn’t.
- d.Number of moles = mass/molar mass; number of gram equivalents = mass/equivalent weight = moles × n. One mole of H₂SO₄ is two gram equivalents.
- e.A primary standard is pure, stable, non-hygroscopic and soluble, so its solution can be made exactly by weighing (oxalic acid, Na₂CO₃, K₂Cr₂O₇). A secondary standard can’t be weighed reliably (it absorbs moisture or CO₂, decomposes, or is a gas), so its solution is standardized against a primary standard (NaOH, HCl, KMnO₄).
- f.An acid–base titration uses a neutralization, H⁺ + OH⁻ → H₂O, and a pH indicator; a redox titration uses a transfer of electrons between an oxidizing and a reducing agent, and a redox indicator or a self-indicating titrant such as KMnO₄.
Volumetric and gravimetric analysis are both kinds of quantitative analysis, useful in the laboratory and in industry.
- a.Define volumetric analysis. How is it different from gravimetric analysis?
- b.What are the uses of volumetric analysis?
- c.Give one limitation of volumetric analysis.
Answer
- a.Volumetric analysis finds the amount or concentration of an analyte by measuring the volume of a standard solution that reacts exactly with it. Gravimetric analysis finds it by measuring a mass, usually of a precipitate that is filtered, dried and weighed. Volumetric analysis is quicker; gravimetric analysis is slower but needs no standard solution and can be very accurate.
- b.Testing water (hardness, chloride, arsenic), medicines (the active ingredient in a tablet), food (the acidity of vinegar, juice and milk), the environment (nitrate and phosphate in rivers), and standardizing solutions in the laboratory.
- c.It needs a reaction that is fast, complete and of known equation, with an end point that can be seen. Very small amounts (traces, a few ppm) can’t be measured accurately by it; instruments are used for those. (Also: a colored or cloudy sample can hide the indicator’s change.)
In a gravimetric analysis, 0.500 g of impure barium chloride is dissolved in water and treated with excess sulphuric acid to precipitate barium sulphate. After filtering and drying, the precipitate weighs 0.434 g. (Ba = 137, Cl = 35.5, S = 32, O = 16)
- a.Write the balanced equation for the reaction.
- b.Calculate the percentage of barium chloride in the sample.
- c.Why is excess sulphuric acid used?
Hint
b. Every mole of BaSO₄ came from one mole of BaCl₂.
Answer
- a.
- b.BaSO₄ = 233 g/mol, BaCl₂ = 208 g/mol. Moles of BaSO₄ = 0.434/233 = 1.863 × 10⁻³ mol = moles of BaCl₂. Mass of BaCl₂ = 1.863 × 10⁻³ × 208 = 0.3874 g.
c. So that all the barium is precipitated: with excess sulphate no Ba²⁺ is left in solution, and the excess also makes BaSO₄ even less soluble. Any barium left dissolved would make the answer too low.
Match each secondary standard with the property that stops it from being a primary standard.
| Substance | Property |
|---|---|
| HCl | it absorbs CO₂ and moisture from the air |
| I₂ | it is decomposed by sunlight |
| H₂SO₄ | it is a gas |
| NaOH | it absorbs moisture from the air |
| KMnO₄ | it sublimes |
Answer
| Substance | Property |
|---|---|
| HCl | it is a gas (its solution loses HCl gas) |
| I₂ | it sublimes |
| H₂SO₄ | it absorbs moisture from the air |
| NaOH | it absorbs CO₂ and moisture from the air |
| KMnO₄ | it is decomposed by sunlight |
- a.Define equivalent weight. Write the relationship between equivalent weight, atomic weight and valency.
- b.Calculate the equivalent weights of H₃PO₄, FeSO₄ and K₂Cr₂O₇ in these reactions (K = 39, Cr = 52, Fe = 56, P = 31, S = 32):
and, for FeSO₄ and K₂Cr₂O₇,
Answer
- a.The equivalent weight of a substance is the mass of it that combines with or displaces 1.008 g of hydrogen, 8 g of oxygen or 35.5 g of chlorine (or, for a compound, the mass that gives or takes one mole of H⁺, OH⁻, charge or electrons in its reaction). For an element, E = A/v, the atomic weight divided by the valency.
- b.H₃PO₄ gives up all three hydrogens (it becomes K₃PO₄): n = 3, E = 98/3 = 32.7.
FeSO₄: Fe goes from +2 to +3, n = 1, E = 152/1 = 152. K₂Cr₂O₇: Cr goes from +6 to +3, two Cr, n = 6, E = 294/6 = 49.
Nitric acid is an important inorganic acid, a strong oxidizing agent with many uses. A bottle of nitric acid is labeled 68% (w/w), specific gravity 1.4 g/mL.
- a.What does 68% (w/w) mean?
- b.Convert this concentration to % w/v.
- c.Calculate the mass of HNO₃ in 1 liter of the solution.
- d.Which of % w/v and % w/w depends on temperature, and why?
Answer
- a.100 g of the solution contains 68 g of HNO₃ (and 32 g of water).
- b.% w/v = % w/w × specific gravity = 68 × 1.4 = 95.2% w/v: 95.2 g of HNO₃ in 100 mL.
- c.95.2 × 10 = 952 g per liter (1 L of the solution weighs 1400 g, and 68% of that is 952 g).
- d.% w/v depends on temperature: it divides by a volume, which grows as the liquid warms. % w/w uses only masses, which don’t change.
- a.State the law of equivalence. How is it useful in titration?
- b.Use it to calculate the mass of magnesium that reacts exactly with 250 mL of decinormal sulphuric acid. (Mg = 24)
Answer
- a.In a chemical reaction, substances react in equal numbers of gram equivalents (and form equal numbers of gram equivalents of products). In a titration, the gram equivalents of titrant used equal those of the analyte, so N₁V₁ = N₂V₂: knowing three of the four quantities gives the fourth, without the balanced equation.
- b.Gram equivalents of acid = 0.1 × 250/1000 = 0.025. The equivalent weight of Mg is 24/2 = 12, so mass of Mg = 0.025 × 12 = 0.3 g.
(Check by moles: ; 0.1 N H₂SO₄ is 0.05 M, 0.25 L holds 0.0125 mol, which reacts with 0.0125 × 24 = 0.3 g of Mg.)
Mohr’s salt, (NH₄)₂Fe(SO₄)₂·6H₂O, is a double salt widely used in analytical chemistry to make a primary standard solution.
- a.What is a standard solution? Why is it important in volumetric analysis?
- b.Give three properties of Mohr’s salt that make it a primary standard.
- c.Why is it called a double salt?
Answer
- a.A standard solution is one whose concentration is known exactly. In volumetric analysis everything is measured against it: the unknown concentration is worked out from the volume of standard solution that reacts with it, so any error in the standard passes into every result.
- b.It is easily got very pure as crystals; it is stable in air (unlike iron(II) sulphate alone, which slowly oxidizes to iron(III) and loses water); it is not hygroscopic; it is readily soluble in water; and it has a large equivalent weight (392), so weighing errors matter little.
- c.It is two simple salts, ammonium sulphate and iron(II) sulphate, crystallized together in a fixed ratio, (NH₄)₂SO₄·FeSO₄·6H₂O. In water it gives just the ions of the two salts (NH₄⁺, Fe²⁺, SO₄²⁻), unlike a complex salt, which keeps a complex ion.
The normal range of glucose in blood (fasting) is about 70–100 milligrams per deciliter (mg/dL). A person’s blood contains 80 mg/dL of glucose. Convert this to:
- a.% w/v
- b.g/L
- c.ppm and ppb
- d.molarity (glucose, C₆H₁₂O₆, M = 180)
Answer
80 mg/dL is 80 mg in 100 mL, that is, 0.080 g in 100 mL.
- a.0.08% w/v.
- b.0.080 × 10 = 0.8 g/L.
- c.0.8 g/L = 800 mg/L, so, taking 1 mL of blood as about 1 g, about 800 ppm, or 8 × 10⁵ ppb. (Blood is a little denser than water, 1.06 g/mL, which makes it 755 ppm by mass.)
- d.0.8/180 = 4.4 × 10⁻³ M (4.4 mmol/L, the unit doctors in many countries use).
Rabin must prepare 500 mL of 0.100 M HCl, but the only HCl solution available is 12.0 M.
- a.Calculate the number of moles in 500 mL of 0.100 M HCl.
- b.What volume of the 12.0 M acid should he use?
- c.What precautions should he take, and why?
Answer
- a.Moles = 0.100 × 0.500 = 0.0500 mol.
- b.M₁V₁ = M₂V₂: 12.0 × V₁ = 0.100 × 500, so V₁ = 4.17 mL.
- c.Concentrated HCl gives off choking, corrosive fumes: work in a fume cupboard or by an open window, with goggles and gloves. Measure it with a burette or graduated pipette with a pipette filler, never by mouth. Put some water (about 300 mL) in the 500 mL volumetric flask first and add the acid to the water, then make up to the mark and mix: acid added to a little water heats less and doesn’t spatter.
A 0.200 g sample of a mixture of NaCl and NaBr is dissolved in water and titrated with 0.100 M AgNO₃.
- a.Name the type of titration. Why is it called so?
- b.If 25.00 mL of AgNO₃ is needed to reach the end point, what is the percentage of NaCl in the mixture? (Na = 23, Cl = 35.5, Br = 80)
The textbook gives a 0.500 g sample, but the numbers don’t work: 25.00 mL of 0.100 M AgNO₃ (0.00250 mol) can react with at most 0.257 g of salt, even if it were all NaBr. A 0.200 g sample is used here.
Hint
b. Let the mass of NaCl be x g. Each mole of NaCl and each mole of NaBr takes one mole of Ag⁺.
Answer
- a.A precipitation titration, also called argentometric (from Latin argentum, silver), because the titrant is a silver salt and the reaction forms a precipitate: , .
- b.Moles of AgNO₃ = 0.100 × 0.02500 = 0.00250 mol = moles of NaCl + moles of NaBr. With x g of NaCl (58.5 g/mol) and 0.200 − x g of NaBr (103 g/mol):
% NaCl = 0.0756/0.200 × 100 = 37.8%.
Potassium permanganate oxidizes oxalic acid in acidic solution.
- a.Write the balanced equation for the reaction.
- b.25 mL of 0.1 M KMnO₄ completely oxidizes 50 mL of oxalic acid solution. Calculate the molarity of the oxalic acid.
Answer
a.
or in ionic form
b. By moles: KMnO₄ = 0.1 × 0.025 = 0.0025 mol; oxalic acid = 0.0025 × 5/2 = 0.00625 mol in 0.050 L: 0.125 M.
By equivalents: KMnO₄ is 0.1 × 5 = 0.5 N; 0.5 × 25 = N × 50 gives N = 0.25 N for the oxalic acid, and with n = 2, M = 0.25/2 = 0.125 M.
Long answer questions
An industrial chemist needs 100 liters of 0.5 N H₂SO₄ for a manufacturing process, and has a bottle labeled 98% (w/w), density 1.84 g/mL.
- a.What does a 0.5 N concentration of the acid mean?
- b.Calculate the volume of the concentrated acid needed.
- c.Discuss the dangers and the precautions in preparing and handling such concentrated acid in large quantities.
Answer
- a.Each liter of the solution holds 0.5 gram equivalents of H₂SO₄: 0.5 × 49 = 24.5 g (0.25 mol).
- b.H₂SO₄ needed = 100 × 0.5 = 50 gram equivalents = 50 × 49 = 2450 g. One liter of the concentrated acid weighs 1840 g, of which 98% is H₂SO₄: 1840 × 0.98 = 1803.2 g/L (18.4 M). Volume = 2450/1803.2 = 1.36 L.
- c.Concentrated sulphuric acid burns skin and eyes, and takes water from anything it touches (it chars paper, cloth and skin). Mixing it with water gives out a great deal of heat. So: wear goggles or a face shield, acid-proof gloves and apron; work where there is good ventilation; add the acid slowly to the water, never water to acid, stirring and letting it cool, in a vessel that can stand the heat; carry the acid in its proper container, with a spill kit (sodium bicarbonate) and running water at hand; label the product clearly.
In biological research, a 2% (w/v) NaCl solution is used to draw water out of cells; it is more concentrated than the cells’ contents (hypertonic), while 0.9% saline is isotonic with them.
- a.What does 2% (w/v) mean?
- b.Calculate the molarity and normality of this solution. (Its density is 1.02 g/mL.)
- c.Why are different units needed for concentration?
Answer
- a.2 g of NaCl in every 100 mL of solution.
- b.g/L = 2 × 10 = 20 g/L. Molarity = 20/58.5 = 0.342 M. NaCl has n = 1, so normality = 0.342 N. (The density isn’t needed for these; it would be needed for % w/w or molality: 1 L weighs 1020 g, so % w/w = 20/1020 × 100 = 1.96%.)
- c.Each unit suits a job. Molarity and normality make titration and reaction sums simple; molality and mole fraction don’t change with temperature, so they are used when solutions are heated or cooled; % and g/L are easy for labels and everyday use (saline, vinegar); ppm and ppb suit tiny amounts of pollutants.
A titration is set up as in Figure 1.9: decimolar (0.1 M) caustic soda in the burette, and 25 mL of 0.2 M oxalic acid solution in the conical flask.
- a.Identify the type of titration, the analyte and the titrant.
- b.Write the equation for the reaction.
- c.Calculate the volume of NaOH needed to react completely with 25 mL of the oxalic acid.
- d.What is the concentration of the salt in the flask when the oxalic acid is half neutralized?
Hint
c. Oxalic acid has two replaceable hydrogens. d. Half neutralized: half the acid’s hydrogens have been replaced.
Answer
- a.An acid–base titration; since a standard base finds the strength of an acid, it is alkalimetry. The analyte is the oxalic acid (in the flask), the titrant is the 0.1 M NaOH (in the burette). (No other acid is added: “acidic medium” belongs to permanganate titrations of oxalic acid, not this one.)
- b.
- c.Oxalic acid: 0.2 M × 2 = 0.4 N. N₁V₁ = N₂V₂: 0.4 × 25 = 0.1 × V, so V = 100 mL. (By moles: 0.2 × 0.025 = 0.005 mol of acid needs 0.010 mol of NaOH, 0.010/0.1 = 0.100 L.) That is more than a 50 mL burette holds, so it would be refilled once; in practice a smaller volume of acid, or a stronger alkali, is chosen.
- d.Half neutralized after 50 mL of NaOH (0.005 mol): . The flask holds 0.005 mol of sodium hydrogen oxalate in 25 + 50 = 75 mL: 0.005/0.075 = 0.0667 M NaHC₂O₄.
100 mL of 0.1 M HCl is mixed with 200 mL of 0.2 M H₂SO₄ to make a mixture of acids.
- a.What does 0.1 M HCl mean?
- b.Find the volume of sulphuric acid from a bottle of 98% (w/v) H₂SO₄ needed to prepare 200 mL of 0.2 M H₂SO₄.
- c.Calculate the normality of the acid mixture.
- d.What happens to the concentration of the mixture when 700 mL of water is added? Calculate the concentration of the diluted solution.
Answer
- a.Each liter of the solution contains 0.1 mol (3.65 g) of HCl.
- b.98% w/v is 98 g in 100 mL, 980 g/L, that is 980/98 = 10 M. M₁V₁ = M₂V₂: 10 × V₁ = 0.2 × 200, so V₁ = 4.0 mL. (The density isn’t needed, because the label is already per volume.)
- c.HCl: 0.1 N × 100 mL = 10 milliequivalents. H₂SO₄: 0.4 N × 200 mL = 80 milliequivalents. Total 90 milliequivalents in 300 mL: 90/300 = 0.3 N.
- d.The concentration falls, and the gram equivalents of acid stay the same: 90 milliequivalents in 300 + 700 = 1000 mL: 0.09 N.
A solution of KMnO₄ is standardized by titrating it against a known amount of oxalic acid, with a mineral acid present, in warm solution:
- a.Why must a solution be standardized before it is used in a titration?
- b.With KMnO₄ in the burette, what is the color change at the end point?
- c.Why is the flask warmed before the titration?
- d.25.00 mL of KMnO₄ solution is needed to titrate 0.250 g of anhydrous oxalic acid, H₂C₂O₄. What is the molarity of the KMnO₄?
Answer
- a.KMnO₄ is a secondary standard: it can’t be got perfectly pure and its solution slowly decomposes (to brown MnO₂, faster in light), so its true concentration isn’t the one weighed out. Standardizing finds its exact concentration; every later result depends on it.
- b.From colorless to pale pink: each drop of purple permanganate is decolorized while oxalic acid is left; the first drop in excess gives a pale pink that lasts about 30 seconds.
- c.The reaction is slow at room temperature; warming to about 60 °C speeds it up so that each drop reacts at once and the end point is sharp. (Once some Mn²⁺ has formed it catalyzes the reaction, so it speeds up as the titration goes on.)
- d.H₂C₂O₄ = 90 g/mol: 0.250/90 = 2.778 × 10⁻³ mol. MnO₄⁻ = 2.778 × 10⁻³ × 2/5 = 1.111 × 10⁻³ mol, in 0.02500 L: 0.0444 M.
(If the oxalic acid were the crystals, H₂C₂O₄·2H₂O, 126 g/mol, the answer would be 0.0317 M.)
Potassium permanganate is used to find the concentration of an iron(II) sulphate solution. In acid, KMnO₄ reacts with Fe²⁺ ions:
- a.How many moles of KMnO₄ react with 1 mole of iron(II) sulphate?
- b.Calculate the equivalent weights of KMnO₄ and FeSO₄ in this reaction. (K = 39, Mn = 55, Fe = 56)
- c.What is the indicator in this titration, and why?
- d.A 25.0 mL sample of iron(II) sulphate solution needs 20.0 mL of 0.02 M KMnO₄ for complete reaction. Calculate the concentration of the iron(II) sulphate solution.
Answer
- a.1 mol of MnO₄⁻ reacts with 5 mol of Fe²⁺, so 1 mol of FeSO₄ needs 1/5 = 0.2 mol of KMnO₄.
- b.KMnO₄ = 158; Mn +7 → +2, n = 5: E = 31.6. FeSO₄ = 152; Fe +2 → +3, n = 1: E = 152.
- c.No separate indicator: KMnO₄ is its own indicator (a self-indicator). It is decolorized while Fe²⁺ remains; the first drop in excess gives a permanent pale pink.
- d.KMnO₄ = 0.02 × 0.0200 = 4.0 × 10⁻⁴ mol; Fe²⁺ = 5 × 4.0 × 10⁻⁴ = 2.0 × 10⁻³ mol in 0.0250 L: 0.08 M. (By equivalents: 0.1 N × 20.0 = N × 25.0, N = 0.08 N, and n = 1 makes it 0.08 M.)
Solve these numerical problems.
- a.A bottle of tile cleaner contains 135 g of HCl and 775 g of water. What is the percentage by mass of HCl?
- b.How many grams of FeSO₄ are there in 1 L of a solution marked 0.35 M FeSO₄?
- c.Calculate the concentration in grams per liter of bench hydrochloric acid of 12 mol/L.
- d.“Concentrated” hydrochloric acid, a common laboratory reagent, is 37.2% HCl by mass, with density 1.19 g/mL. What mass of HCl is in 0.500 L of it?
- e.What volume of 0.01 M KMnO₄ solution contains 5 g of KMnO₄?
- f.1 g of caustic soda is added to 2 liters of X M sulphuric acid, and the solution is then exactly neutral (pH 7). Find X.
- g.What volumes of 12 M and 2 M NaOH solution must be mixed to make 2 liters of 9 M solution?
- h.Calculate the volume of 1 M NaOH needed to neutralize 200 mL of 2 N HCl. What mass of NaCl is formed?
- i.Two liters of molar H₂SO₄ are mixed with one liter of normal NaOH. Calculate the strength of the mixture and the mass of salt formed.
- j.50 mL of 2 N H₂SO₄ is mixed with 30 mL of 3 N NaOH. Is the solution acidic, basic or neutral? Calculate its strength.
- k.Lye is solid sodium hydroxide sold for cleaning. 1.20 g of lye needs 45.0 mL of 0.5 M hydrochloric acid to neutralize it. Calculate the percentage purity of the NaOH.
- l.5.125 g of washing soda crystals are dissolved and made up to 250 mL. 25.0 mL of this solution needs 35.8 mL of 0.05 M sulphuric acid for complete neutralization. Calculate the percentage of sodium carbonate in the crystals.
- m.A person may die if the alcohol in their blood goes above 500 mg per 100 mL. What is the molar concentration of ethanol at this level?
- n.6.615 g of Mohr’s salt, (NH₄)₂Fe(SO₄)₂·nH₂O, are dissolved in dilute acid and made up to 250 mL. 25.0 mL of this solution needs 22.5 mL of 0.015 M potassium permanganate at the end point. Calculate n.
- o.A commercial bleach contains 3.62% NaOCl by mass in water. Calculate i. the mole fraction and ii. the molality of NaOCl in it.
The textbook gives 8.492 g of the salt in n., but the numbers don’t work: they give a molar mass of 503 g/mol and n = 12.2, not a whole number (Mohr’s salt is the hexahydrate, 392 g/mol). With 6.615 g they give n = 6.
Answer
- a.Mass of solution = 135 + 775 = 910 g; % HCl = 135/910 × 100 = 14.8%.
- b.FeSO₄ = 152 g/mol: 0.35 × 152 = 53.2 g in each liter.
- c.12 × 36.5 = 438 g/L.
- d.Mass of solution = 500 × 1.19 = 595 g; HCl = 595 × 0.372 = 221 g.
- e.5/158 = 0.03165 mol; V = 0.03165/0.01 = 3.17 L.
- f.NaOH: 1/40 = 0.025 mol. , so H₂SO₄ = 0.0125 mol in 2 L: X = 0.00625 M.
- g.Let V L of 12 M be mixed with (2 − V) L of 2 M: 12V + 2(2 − V) = 9 × 2, so 10V = 14 and V = 1.4. 1.4 L of 12 M and 0.6 L of 2 M.
- h.HCl: 2 × 0.200 = 0.400 equivalents; 1 M NaOH is 1 N, so V = 0.400/1 = 0.400 L (400 mL). NaCl formed = 0.400 mol × 58.5 = 23.4 g.
- i.H₂SO₄: 2 L × 2 N = 4 equivalents; NaOH: 1 L × 1 N = 1 equivalent. 3 equivalents of acid are left, in 3 L: the mixture is 1 N acid (0.5 M H₂SO₄). Salt: the 1 equivalent of NaOH forms 1 equivalent of Na₂SO₄, 0.5 mol × 142 = 71 g (counted as Na₂SO₄, as these problems do; with so much acid left over, the sodium is really present as sodium hydrogen sulphate, NaHSO₄).
- j.H₂SO₄: 2 × 50 = 100 milliequivalents; NaOH: 3 × 30 = 90 milliequivalents. The acid is in excess, so the solution is acidic: 10 milliequivalents in 80 mL, 0.125 N acid.
- k.HCl = 0.5 × 0.0450 = 0.0225 mol = NaOH. Mass = 0.0225 × 40 = 0.90 g; purity = 0.90/1.20 × 100 = 75%.
- l.
H₂SO₄ = 0.05 × 0.0358 = 1.79 × 10⁻³ mol = Na₂CO₃ in 25.0 mL; in 250 mL, 1.79 × 10⁻² mol = 1.79 × 10⁻² × 106 = 1.897 g. % = 1.897/5.125 × 100 = 37.0%. (Washing soda crystals, Na₂CO₃·10H₂O, are 37.1% Na₂CO₃: these are pure crystals.)
- m.500 mg per 100 mL is 5 g/L; ethanol (C₂H₅OH) = 46 g/mol: 5/46 = 0.109 M.
- n.KMnO₄ = 0.015 × 0.0225 = 3.375 × 10⁻⁴ mol; Fe²⁺ = 5 × that = 1.6875 × 10⁻³ mol in 25.0 mL, so 1.6875 × 10⁻² mol in 250 mL, and as each formula unit holds one Fe²⁺, the same number of moles of the salt. Molar mass of the salt = 6.615/0.016875 = 392 g/mol. The anhydrous salt, (NH₄)₂Fe(SO₄)₂, is 284, so 18n = 392 − 284 = 108 and n = 6: the salt is (NH₄)₂Fe(SO₄)₂·6H₂O.
- o.Take 100 g: NaOCl 3.62 g = 3.62/74.5 = 0.0486 mol; water 96.38 g = 96.38/18 = 5.354 mol.
- i.χ(NaOCl) = 0.0486/(0.0486 + 5.354) = 0.0090.
- ii.Molality = 0.0486/0.09638 kg = 0.504 m.
