Exam practice
Every question from the end of every unit, with hints and answers to open. After you check an answer, mark how you did, and come back to the ones you didn’t get.
9 questions
Unit 25 · Solids
Printable PDFs
- The unit as a book (A5) 22 pages Answers as an A4 booklet, 6 sheets
- Study notes 3 pages
- Worksheet 5 pages Answer key
- Harder practice questions 2 pages Answer key
Answer these questions
On the basis of the band theory of solids, how would you distinguish between a conductor and a semiconductor?
Answer
- In a conductor, the highest band containing electrons is only partly filled, or the valence and conduction bands overlap. There is no gap to cross: plenty of empty levels lie just above the electrons, so they gain energy from an electric field and carry a current at any temperature. More heat adds no carriers, only more scattering, so resistance rises with temperature.
- In a semiconductor, the valence band is full and the conduction band empty at 0 K, separated by a small forbidden gap of about 1 eV. At 0 K it is an insulator. At room temperature a few electrons jump the gap, leaving holes, and both carry a small current; the warmer it is, the more jump, so its resistance falls as the temperature rises.
How is a p-type semiconductor formed? Explain.
Answer
Pure silicon (or germanium) is doped with a small amount of a trivalent impurity: boron, aluminium, gallium or indium. Each impurity atom takes a silicon atom’s place in the crystal and bonds with four silicon neighbors, but it has only three outer electrons, so one bond is an electron short: a hole. An electron from a nearby bond easily moves into it, so the hole moves off through the crystal, and the impurity atom becomes a fixed negative ion; it is called an acceptor. The holes far outnumber the free electrons, so holes are the majority carriers: a p-type semiconductor. The crystal as a whole stays neutral.
When p-type and n-type materials are joined, a depletion layer forms at the junction. Why?
Answer
The n side has many free electrons and the p side many holes. Near the junction, free electrons diffuse into the p side and holes into the n side, from where they are many to where they are few, and they recombine. So a thin layer either side of the junction is left with no free carriers: it is depleted of them. What remains there are the fixed ions, positive donors on the n side and negative acceptors on the p side. Their electric field (the barrier potential, about 0.7 V in silicon) pushes back further carriers, so the layer stops growing at about a micrometer.
How does the conductivity of a semiconductor vary with temperature? Explain.
Answer
It increases as the temperature rises (its resistance falls). At higher temperatures more electrons gain enough thermal energy to jump the forbidden gap into the conduction band, and each leaves a hole in the valence band, so the number of charge carriers grows steeply: for silicon, about ten times for every 30 °C or so near room temperature. The atoms also vibrate more, which scatters the carriers and on its own would lower the conductivity, but the growth in the number of carriers far outweighs it.
The conductivity of an intrinsic semiconductor is low. Why?
Answer
In a pure semiconductor, almost every electron is held in a covalent bond (a full valence band). Only the electrons that gain enough thermal energy to cross the band gap (about 1 eV) become free, and at room temperature, with only about 0.04 eV, very few do: about 10¹⁶ per cubic meter in silicon, against about 10²⁹ in copper. With so few electrons and holes to carry charge, the conductivity is low.
Why is a semiconductor virtually an insulator at room temperature?
Answer
For the same reason as in question 17: its band gap (about 1 eV) is about 25 times the average thermal energy at room temperature (about 0.04 eV), so only about one bond in 10¹³ is broken. The valence band is almost full and the conduction band almost empty, so there are very few free electrons and holes. Pure silicon’s resistivity is about 10¹¹ times copper’s: in practice it is a very poor conductor, until it is doped.
What do you mean by doping?
Answer
Doping is adding a small, controlled amount of a suitable impurity to a pure (intrinsic) semiconductor to increase its conductivity, typically one impurity atom per 10⁶–10⁸ atoms. Pentavalent impurities (P, As, Sb), donors, give extra free electrons and make n-type semiconductors; trivalent impurities (B, Al, Ga, In), acceptors, give holes and make p-type semiconductors.
What do you mean by the forbidden energy gap?
Answer
The forbidden energy gap (band gap, ) is the range of energies between the top of the valence band and the bottom of the conduction band, in which an electron in the solid can have no energy at all. An electron must gain at least to move from the valence band to the conduction band. It is about 1 eV in semiconductors (Si 1.12 eV, Ge 0.67 eV), 5–10 eV in insulators, and zero in conductors, whose bands overlap.
What is an extrinsic semiconductor? Explain the formation of the potential barrier and the depletion layer at a p–n junction.
Answer
An extrinsic semiconductor is a semiconductor that has been doped with an impurity to increase its conductivity: n-type (pentavalent donors, electrons the majority carriers) or p-type (trivalent acceptors, holes the majority carriers).
At a p–n junction:
- The n side has many free electrons and the p side many holes. Near the junction, electrons diffuse across into the p side and holes into the n side, and they recombine.
- This leaves a thin layer with no free carriers, the depletion layer, containing only the fixed ions: positive donor ions on the n side, negative acceptor ions on the p side.
- These charges make an electric field across the layer, from the n side to the p side, which pushes back more electrons trying to cross from n to p (and holes from p to n). Diffusion stops when this field is strong enough.
- The potential difference across the depletion layer is the potential barrier: about 0.7 V in silicon, 0.3 V in germanium. A forward bias larger than it lets current flow; a reverse bias widens the layer and stops it.
