Exam practice
Every question from the end of every unit, with hints and answers to open. After you check an answer, mark how you did, and come back to the ones you didn’t get.
31 questions
Unit 12 · Heat
Printable PDFs
- The unit as a book (A5) 29 pages Answers as an A4 booklet, 8 sheets
- Study notes 2 pages
- Worksheet 5 pages Answer key
- Harder practice questions 2 pages Answer key
2. Give reasons
A wet cloth on the forehead brings down a high fever.
Hint
What does the water in the cloth do, and what does it need to do it?
Answer
The water in the cloth evaporates. The molecules that escape are the most energetic ones, and the heat to replace their energy (the latent heat of vaporization, about 2,400,000 J for every kilogram) is taken from the forehead. So the skin, and the blood flowing under it, cool down.
Small gaps are left between the rails of a railway track.
Hint
What happens to steel rails on a hot day?
Answer
Steel rails expand on hot days (linear expansion). If they were laid end to end with no gaps, they would push on each other with huge forces and bend sideways (buckle), which could derail a train. The gaps give each rail room to get longer.
Ice at 0 °C cools a drink better than the same mass of water at 0 °C.
Hint
What must happen to the ice before it can warm up?
Answer
Ice must first melt, and each kilogram takes in 336,000 J of latent heat from the drink while melting, without any change in its own temperature. Only then does it warm up like water. Water at 0 °C only takes in heat by warming. So the ice takes far more heat from the drink and cools it more.
Clothes dry faster on a windy day than on a still day.
Hint
Where do the escaped water molecules go in still air?
Answer
In still air, the water vapor that escapes from the clothes collects around them, the air there becomes humid, and many molecules return to the cloth. Wind carries the vapor away and brings dry air, so fewer molecules return and evaporation is faster.
A burn from steam at 100 °C is more severe than one from boiling water at 100 °C.
Hint
What does steam do first when it touches the skin, and what does it give out?
Answer
When steam touches the skin, it first condenses into water at 100 °C, giving out its latent heat of vaporization, 2,260 J for every gram, and only then cools like boiling water. So the same mass of steam gives the skin about ten times as much heat as boiling water.
Electric wires are hung with some sag between the poles.
Hint
What happens to the wires on a cold winter night?
Answer
Wires contract in cold weather. If they were hung tight, they would pull hard on the poles in winter and could snap. The sag leaves room for them to get shorter.
The temperature of water does not rise while it is boiling, though it is still being heated.
Hint
What is the heat being used for during boiling?
Answer
At the boiling point, all the heat supplied is used as latent heat: it pulls the molecules completely away from each other and pushes back the air to make room for the vapor. It raises their potential energy, not their kinetic energy, so the average kinetic energy, and so the temperature, stays the same until all the water has boiled away.
3. Differentiate between
Evaporation and boiling
Hint
Where does each happen, at what temperature, how fast, and what happens to the liquid’s temperature?
Answer
| Evaporation | Boiling |
|---|---|
| Happens only at the surface of the liquid. | Happens all through the liquid, with bubbles. |
| Happens at any temperature. | Happens at a fixed temperature, the boiling point. |
| Slow and quiet. | Fast and vigorous. |
| Cools the liquid. | The temperature stays constant while heat is supplied. |
| Depends on surface area, wind and humidity. | Doesn’t depend on them. |
Linear, superficial and cubical expansion
Hint
What grows in each, and on what kinds of object does it matter?
Answer
| Linear expansion | Superficial expansion | Cubical expansion |
|---|---|---|
| Increase in length on heating. | Increase in area on heating. | Increase in volume on heating. |
| Matters for long, thin things. | Matters for flat things. | Matters for blocks, liquids and gases. |
| Rails, wires, rods. | Metal sheets, roofs, tiles. | A metal ball, mercury in a thermometer, air in a tyre. |
| Shown by a rod turning a pointer. | Shown by a coin and a hole. | Shown by the ball and ring. |
Latent heat of fusion and latent heat of vaporization
Hint
Which change of state, at which temperature, and how big for water?
Answer
| Latent heat of fusion | Latent heat of vaporization |
|---|---|
| Heat needed to change a solid into a liquid at its melting point. | Heat needed to change a liquid into a vapor at its boiling point. |
| Given out when the liquid freezes. | Given out when the vapor condenses. |
| The molecules are only loosened; they still touch. | The molecules are pulled completely apart, and the vapor pushes back the air. |
| For ice, 336,000 J/kg. | For water, 2,260,000 J/kg, about 6.7 times larger. |
Specific heat capacity and specific latent heat
Hint
What does each measure, and what are their units?
Answer
| Specific heat capacity | Specific latent heat |
|---|---|
| Heat needed to raise the temperature of 1 kg of a substance by 1 °C. | Heat needed to change the state of 1 kg of a substance at constant temperature. |
| The temperature changes. | The temperature doesn’t change. |
| Increases the kinetic energy of the molecules. | Increases the potential energy of the molecules. |
| ; unit J/(kg °C). | ; unit J/kg. |
| Water: 4,200 J/(kg °C). | Water: 336,000 J/kg (fusion), 2,260,000 J/kg (vaporization). |
4. Answer the following questions
What is evaporation? Explain, using the kinetic theory of matter, why evaporation causes cooling.
Hint
Molecules in a liquid have a range of speeds. Which ones escape, and what happens to the average of those left?
Answer
Evaporation is the change of a liquid into its vapor from its surface, at any temperature below its boiling point.
The molecules of a liquid move with a range of speeds, and the temperature depends on their average kinetic energy. Only the fastest molecules at the surface have enough energy to break free of the attraction of their neighbors and escape into the air. When the most energetic molecules leave, the average kinetic energy of the molecules left behind falls, so the temperature of the liquid falls. Heat then flows into the liquid from its surroundings, so they cool too. This is the cooling effect of evaporation, seen in sweating and in the clay matka.
Describe the factors that affect the rate of evaporation, with an example of each.
Hint
There are six: think of drying clothes.
Answer
- Temperature: the hotter the liquid, the more molecules are fast enough to escape. Clothes dry faster in the sun.
- Surface area: molecules escape only from the surface, so a larger surface evaporates faster. Tea cools faster in a saucer; grains are spread thin to dry.
- Humidity: in humid air many vapor molecules return to the liquid, so evaporation is slow. Clothes dry slowly in the monsoon.
- Wind: moving air carries the vapor away. Clothes dry faster on a windy day; fanning cools a wet face.
- Nature of the liquid: liquids with weaker forces between their molecules (spirit, petrol) evaporate faster than water.
- Air pressure: lower air pressure lets molecules escape more easily, so evaporation is faster at high altitude.
Explain thermal expansion of a solid in terms of the motion of its molecules.
Hint
How do the molecules of a solid move, and what does heating do to that motion?
Answer
The molecules of a solid vibrate about fixed places, held by the forces between them. When the solid is heated, they gain energy and vibrate with bigger swings. The force between two molecules pushes back much more strongly when they are squeezed together than it pulls when they move apart, so with bigger swings each molecule moves much farther outward than inward, and its average distance from its neighbors increases. Every distance between neighboring molecules grows a little, so the solid grows in length, area and volume: it expands. On cooling, the swings get smaller and the solid contracts.
Write four impacts of thermal expansion in daily life, and how each is dealt with or used.
Hint
Think of railways, bridges, wires, glass, thermostats and filling bottles.
Answer
Any four of:
- Railway tracks would buckle in the heat: gaps or expansion joints are left between rails.
- Bridges grow and shrink: they rest on rollers at one end and have expansion joints in the road.
- Overhead wires would snap in winter: they are hung with a sag.
- Thick glass cracks when hot liquid is poured in: cooking glass is made of borosilicate glass, which expands little.
- Bottles and petrol tanks filled to the brim overflow or burst in the heat: a space is left at the top.
- Bimetallic strips use expansion to switch circuits in thermostats, fire alarms and circuit breakers.
- Iron tyres are fitted on cart wheels while hot, and grip tightly as they cool.
Define latent heat. Explain, using the kinetic molecular theory, why the temperature of melting ice stays at 0 °C while it is heated.
Hint
Molecules have kinetic and potential energy. Which one does the heat raise during melting?
Answer
Latent heat is the heat absorbed or given out by a substance during a change of state, without any change in its temperature.
The temperature of a substance depends on the average kinetic energy of its molecules. In ice, the molecules are held in fixed places by their attraction for each other. At 0 °C, the heat supplied doesn’t make them vibrate any faster; it is used to pull them free of their fixed places against those forces, which increases their potential energy. Since their kinetic energy doesn’t change, the temperature stays at 0 °C until all the ice has melted. Only then does the heat raise the molecules’ kinetic energy again, and the temperature rises.
Why is the latent heat of vaporization of water greater than its latent heat of fusion?
Hint
Compare how far apart the molecules end up after melting and after boiling.
Answer
In melting, the molecules are only loosened from their fixed places; in the liquid they are still close together and still attract each other. In boiling, each molecule must be pulled completely away from all its neighbors, so much more work is done against the forces between them. The vapor also takes up about 1,600 times the volume of the water, and pushing back the atmosphere to make that room takes more energy still. So the latent heat of vaporization (2,260,000 J/kg) is about 6.7 times the latent heat of fusion (336,000 J/kg).
State the heat equation. Write the formulas used with it for a change of temperature and a change of state.
Hint
It is energy conservation for a hot body and a cold body together.
Answer
Heat equation (principle of calorimetry): when a hot body and a cold body are in contact in an insulated system, the heat lost by the hot body is equal to the heat gained by the cold body, until both are at the same temperature.
For a change of temperature, , where is the mass, the specific heat capacity and the change in temperature.
For a change of state at constant temperature, , where is the specific latent heat.
Sketch the graph of temperature against time when ice at −20 °C is heated steadily until it becomes steam at 120 °C. Label each part and say what is happening in it.
Hint
Five parts: three slopes and two flat stretches. Which flat stretch is longer?
Answer
The graph rises steeply from −20 °C to 0 °C (the ice warms), stays flat at 0 °C (the ice melts: ice and water together, latent heat of fusion), rises from 0 °C to 100 °C (the water warms, less steeply than the ice because water’s specific heat capacity is about twice ice’s), stays flat at 100 °C for a long time (the water boils: water and steam together, latent heat of vaporization), then rises again from 100 °C (the steam warms). The boiling stretch is about 6.7 times as long as the melting stretch, because the latent heat of vaporization is about 6.7 times the latent heat of fusion. The HeatingCurve widget in 12.3 draws it to scale.
How is a bimetallic strip used in the thermostat of an electric iron?
Hint
What does the strip do when it gets hot, and what is at its tip?
Answer
A bimetallic strip of two metals that expand by different amounts (such as brass and iron) is placed in the iron’s heater circuit, with its tip touching a contact. While the iron is cool, the strip is straight, the contact is closed and current flows through the heater. When the iron reaches the set temperature, the metal that expands more makes the strip bend away from the contact, the circuit is broken and the heater switches off. As the iron cools, the strip straightens, touches the contact again and the heater switches on. Turning the knob moves the contact closer or farther, which sets the temperature at which this happens.
5. Numerical problems
How much heat is needed to melt 500 g of ice at 0 °C? (L = 336,000 J/kg)
Hint
No temperature change: , with the mass in kilograms.
Answer
168,000 J.
How much heat is needed to change 2 kg of water at 100 °C into steam at 100 °C? (L = 2,260,000 J/kg)
Hint
again, with the latent heat of vaporization.
Answer
4.52 × 10⁶ J.
Find the heat needed to change 0.5 kg of ice at −5 °C into water at 0 °C. (s of ice = 2,100 J/(kg °C); L = 336,000 J/kg)
Hint
Two steps: warm the ice to 0 °C, then melt it.
Answer
Warm the ice:
Melt it:
= 173,250 J.
How much heat does it take to turn 100 g of water at 20 °C into steam at 100 °C? (s of water = 4,200 J/(kg °C); L = 2,260,000 J/kg)
Hint
Warm the water to 100 °C, then boil it.
Answer
Warm:
Boil:
= 259,600 J.
Find the heat needed to change 1 kg of ice at −10 °C into steam at 100 °C. What share of it is used in boiling?
Hint
Four steps: warm the ice, melt it, warm the water, boil it. Use 2,100 and 4,200 J/(kg °C), 336,000 and 2,260,000 J/kg.
Answer
Warm the ice:
Melt it:
Warm the water:
Boil it:
Total = 3,037,000 J (about 3.04 × 10⁶ J). Boiling takes = about 74% of it.
A 500 W heater is put in a large block of ice at 0 °C. How long does it take to melt 1 kg of the ice, if all its heat goes into the ice?
Hint
Find the heat needed, then time = heat ÷ power.
Answer
672 s, about 11.2 minutes.
Rizwan adds 40 g of ice at 0 °C to 200 g of water at 25 °C. Find the final temperature, assuming all the ice melts and no heat is lost.
Hint
Heat lost by the water cooling from 25 °C to = heat to melt the ice + heat to warm its water from 0 °C to .
Answer
Heat lost:
Heat gained:
, so .
7.5 °C. (Check: the water could give 21,000 J by cooling to 0 °C, more than the 13,440 J the ice needs to melt, so all the ice does melt.)
How much steam at 100 °C must be passed into 500 g of water at 20 °C to warm it to 80 °C?
Hint
The steam condenses, then its water cools from 100 °C to 80 °C. Call its mass .
Answer
Heat gained by the water:
Heat lost by kg of steam:
, so .
About 54 g of steam.
A copper calorimeter of mass 200 g contains 300 g of water at 30 °C. 50 g of ice at 0 °C is added. Find the final temperature once all the ice has melted. (s of copper = 385 J/(kg °C))
Hint
The water and the calorimeter cool from 30 °C to .
Answer
Heat lost by the water and the calorimeter:
Heat gained by the ice:
, so .
About 15.1 °C.
In an experiment, a 1,500 W kettle kept boiling for 10 minutes boils away 0.39 kg of water. Find the latent heat of vaporization from these readings. Why is your answer larger than 2,260,000 J/kg?
Hint
, with the time in seconds.
Answer
About 2.31 × 10⁶ J/kg. It is larger because not all the kettle’s 900,000 J went into boiling water: some heat escaped to the air and warmed the kettle itself. Dividing all of it by the mass boiled away gives too large a value.
Think: 50 g of ice at 0 °C cools 250 g of juice at 30 °C to about 11.7 °C (Example 5). Find the final temperature if 50 g of water at 0 °C is used instead, and explain the difference.
Hint
Water at 0 °C only warms; it doesn’t melt first.
Answer
Heat lost by the juice = heat gained by the cold water:
, so .
25 °C, against 11.7 °C with ice. The ice takes 16,800 J from the juice just to melt, without warming at all, before its water starts to warm like the cold water. That latent heat does most of the cooling.
