Skip to content

← Grade 10 Optional Science

Exam practice

Every question from the end of every unit, with hints and answers to open. After you check an answer, mark how you did, and come back to the ones you didn’t get.

26 questions

Unit 14 · Electricity and Magnetism

2. Give reasons

a.

A ferromagnetic material is attracted far more strongly than a paramagnetic material.

Hint

Think about domains: what is already lined up in one material, and what keeps things random in the other?

Answer

In a ferromagnetic material the atomic magnets are already lined up in domains, and a field turns whole domains to point along it, so the material becomes a strong magnet. In a paramagnetic material the atomic magnets point at random and are kept random by heat; a field can line up only a tiny share of them, so it becomes only a very weak magnet.

b.

A lead-acid battery is called a storage battery.

Hint

What happens to the charger’s electrical energy, and what happens to it when the battery is used?

Answer

When it is charged, the electrical energy from the charger is stored as chemical energy (lead dioxide, lead and sulphuric acid are made again). When it is used, the stored chemical energy is given back as electrical energy. It stores energy and gives it back many times over.

c.

A lead-acid battery should be charged in an open, airy place away from flames.

Hint

Which gases bubble out near the end of charging, and what do they make together?

Answer

Near the end of charging, the current splits water in the acid into hydrogen and oxygen, which bubble out of the vents. Together they form an explosive mixture; in a closed room it can collect, and a flame or a spark can make it explode.

d.

An ammeter should have a very low resistance and a voltmeter a very high one.

Hint

Remember how each one is connected, and ask what its own resistance would do to the current it is meant to measure.

Answer

An ammeter is put in series, so all the current passes through it. If its resistance were large, it would reduce the current it is measuring. A voltmeter is put in parallel; if its resistance were low, it would take a large share of the current away from the part it is across and change the voltage it is measuring. A very high resistance means it takes almost no current.

e.

The pointer of a galvanometer swings both ways from a zero in the middle of its scale.

Hint

What happens to the forces on the coil’s sides when the current is reversed? And what is a galvanometer used to find out?

Answer

The turning effect on the coil depends on the direction of the current: reversing the current reverses the forces on the coil’s sides, so the coil turns the other way. A galvanometer is used to detect small currents and to show which way they flow, so its zero is in the middle and it can swing either way.

3. Differentiate between

i.

Primary cell and secondary cell

Hint

Compare recharging, the reaction, the current they can give, their cost over time, and an example of each.

Answer
Primary cell Secondary cell
Can’t be recharged. Can be recharged many times.
Its chemical reaction is irreversible. Its chemical reaction is reversed by charging.
Gives a small current; fairly high internal resistance. Can give a large current; very low internal resistance.
Cheaper to buy, costlier over time. Costlier to buy, cheaper over its life.
Example: dry cell (zinc–carbon). Example: lead-acid cell, lithium-ion cell.
ii.

Ammeter and voltmeter

Hint

Compare what each measures, how it is connected, its resistance, and what is added to a galvanometer to make it.

Answer
Ammeter Voltmeter
Measures electric current, in amperes. Measures potential difference, in volts.
Connected in series. Connected in parallel.
Has a very low resistance. Has a very high resistance.
Made from a galvanometer with a low resistance (shunt) in parallel. Made from a galvanometer with a high resistance (multiplier) in series.
iii.

p-type and n-type semiconductors

Hint

Compare what is added to the silicon (how many outer electrons it has) and which charges carry the current.

Answer
p-type semiconductor n-type semiconductor
Made by adding an element with three outer electrons (boron, gallium) to silicon. Made by adding an element with five outer electrons (phosphorus, arsenic) to silicon.
The charges that move are mostly holes, which act as positive charges. The charges that move are mostly free electrons, which are negative.

4. Answer the following questions

a.

What is molecular magnetism? Draw the arrangement of the atomic magnets in a paramagnetic and a ferromagnetic material, with no field and in a strong field.

Hint

Start from unpaired electrons. Then four drawings: each material with no field and in a strong field; only the ferromagnetic one has domains.

Answer

In some substances, each atom or molecule has unpaired electrons whose magnetic fields don’t cancel, so each atom or molecule is a tiny magnet: this is molecular magnetism. Drawings (as in the activity of 14.1):

  • paramagnetic, no field: small arrows pointing every which way;
  • paramagnetic, strong field: still nearly random, leaning only slightly towards the field (draw them tilted partly towards it and write “only a tiny share line up”);
  • ferromagnetic, no field: regions (domains), each with all its arrows one way, different regions different ways;
  • ferromagnetic, strong field: all the domains’ arrows along the field.
b.

Describe the structure of a lead-acid cell with a labeled diagram.

Hint

Name the case, the two plates and what each is made of, the electrolyte with its density, the separators and the vent cap, and the cell’s voltage.

Answer

A lead-acid cell has a plastic case holding dilute sulphuric acid (about 1.28 g/cm³ when charged). In it stand a positive plate of lead dioxide (PbO₂, brown) and a negative plate of spongy lead (Pb, gray), each on a grid of lead alloy, kept apart by porous separators; real cells have several plates of each kind joined in parallel. A vent cap lets out the gases made while charging. The cell gives about 2 V. The diagram shows the case, the acid, the two plates with their + and − terminals and the separator, as in the widget in 14.2.

c.

Write the chemical reactions at each plate of a lead-acid cell while it is discharging. What happens to them during charging?

Hint

Both plates end up as PbSO₄. Balance each half-equation with electrons, then add them.

Answer

At the negative plate: Pb + SO₄²⁻ → PbSO₄ + 2e⁻.
At the positive plate: PbO₂ + 4H⁺ + SO₄²⁻ + 2e⁻ → PbSO₄ + 2H₂O.
Overall: Pb + PbO₂ + 2H₂SO₄ → 2PbSO₄ + 2H₂O.
During charging, a current passed the other way reverses every reaction: 2PbSO₄ + 2H₂O → Pb + PbO₂ + 2H₂SO₄. Lead dioxide and lead are formed again on the plates, and the sulphuric acid becomes stronger again.

d.

Explain the structure and working of a moving-coil galvanometer.

Hint

Parts: coil, magnet with curved poles, soft-iron core, hairsprings, pointer. Working: the motor effect on the coil’s two sides, balanced by the springs.

Answer

It has a coil of many turns of fine insulated copper wire on a light frame, free to turn on an axle between the curved pole pieces of a strong permanent magnet, with a fixed soft-iron cylinder inside the coil that makes the field strong and radial. Two hairsprings hold the coil at zero and lead the current in and out; a pointer fixed to the coil moves over a scale.
When a current flows, the two sides of the coil carry it in opposite directions in the field, so by the motor effect one side is pushed one way and the other the other way, and the coil turns. It twists the hairsprings until their push balances the turning effect. The deflection is proportional to the current, and reverses when the current reverses.

e.

What is a diode? Explain forward and reverse bias, and give two uses of diodes.

Hint

Which side of the p–n junction goes to the + terminal in each case, and what happens to the holes, the electrons and the depletion layer?

Answer

A diode is a p–n junction of semiconductor that lets current through in one direction only. Forward bias: the p side is joined to the positive terminal; holes and electrons are pushed to the junction and cross it, and current flows (once the voltage is above about 0.7 V for silicon). Reverse bias: the p side is joined to the negative terminal; the charges are pulled away from the junction, the depletion layer widens, and practically no current flows. Uses: as a rectifier, changing a.c. to d.c. in chargers and adapters; as an LED for lighting; also in solar cells and to protect circuits from batteries put in the wrong way.

f.

What is a transistor? How can it be used as a switch and as an amplifier?

Hint

Three layers and three terminals; then the key idea: a small base current controls a large collector current.

Answer

A transistor is a three-layer semiconductor device, npn or pnp, with three terminals: emitter, base and collector. A small current into the base controls a much larger current between the collector and the emitter, typically about 100 times bigger. As a switch: with no base current it is off; a small base current turns on a large collector current, as in an automatic night light, where an LDR sets the base voltage, or in a computer chip. As an amplifier: a small, changing base current (from a microphone, say) makes a large collector current that changes in the same way, a stronger copy of the signal that can drive a loudspeaker.

g.

Think: in the night light of Figure 14.6, what would happen if the LDR and the 10 kΩ resistor were swapped, so that the LDR was between +6 V and the base?

Hint

The base now gets the share of the 6 V across the fixed resistor. Work it out for 1 kΩ and 100 kΩ.

Answer

The base voltage would now be the share of the 6 V across the fixed resistor, which is the lower part. In daylight the LDR’s resistance is low (1 kΩ), so the base gets 6 × 10/11 ≈ 5.5 V and the transistor is on; in the dark (100 kΩ) the base gets 6 × 10/110 ≈ 0.55 V and it is off. The lamp would come on in the light and go off in the dark: a circuit that works as a light alarm, for example to warn when a fridge or a darkroom door is opened.

5. Numerical problems

a.

A galvanometer of resistance 100 Ω gives full-scale deflection for a current of 1 mA. (i) What potential difference across it gives full-scale deflection? (ii) What shunt makes it an ammeter of range 0–1 A? (iii) What resistance in series makes it a voltmeter of range 0–5 V?

Hint

For (i), V=IgG V = I_gG . For (ii), the shunt formula S=IgGI−Ig S = \frac{I_gG}{I - I_g} ; for (iii), R=VIg−G R = \frac{V}{I_g} - G . Change mA into A first.

Answer
  • i.V=IgG=0.001×100=0.1 V V = I_gG = 0.001 \times 100 = 0.1\ \text{V} .
  • ii.S=IgGI−Ig=0.001×1001−0.001=0.10.999=0.100 Ω S = \frac{I_gG}{I - I_g} = \frac{0.001 \times 100}{1 - 0.001} = \frac{0.1}{0.999} = 0.100\ \Omega
  • iii.R=VIg−G=50.001−100=4,900 Ω R = \frac{V}{I_g} - G = \frac{5}{0.001} - 100 = 4{,}900\ \Omega

So: 0.1 V for full scale, a 0.100 Ω shunt in parallel for the ammeter, and 4,900 Ω in series for the voltmeter.

b.

A galvanometer of resistance 50 Ω gives full-scale deflection for 10 mA. Find the shunt needed to make it an ammeter of range 0–2 A, and the resistance of the whole ammeter.

Hint

Use S=IgGI−Ig S = \frac{I_gG}{I - I_g} , then the two resistances in parallel, GSG+S \frac{GS}{G + S} .

Answer

S=0.01×502−0.01=0.51.99=0.251 Ω S = \frac{0.01 \times 50}{2 - 0.01} = \frac{0.5}{1.99} = 0.251\ \Omega
Whole ammeter: GSG+S=50×0.25150.251=0.25 Ω \frac{GS}{G + S} = \frac{50 \times 0.251}{50.251} = 0.25\ \Omega . (Also: at full scale, 0.5 V drives 2 A through it, and 0.5 ÷ 2 = 0.25 Ω.)
A shunt of 0.251 Ω; the ammeter’s resistance is 0.25 Ω.

c.

The same galvanometer (50 Ω, 10 mA) is to read up to 20 V. What resistance must be connected, and how? What is the resistance of the voltmeter?

Hint

A voltmeter: a resistance in series, R=VIg−G R = \frac{V}{I_g} - G .

Answer

R=200.01−50=2,000−50=1,950 Ω R = \frac{20}{0.01} - 50 = 2{,}000 - 50 = 1{,}950\ \Omega
1,950 Ω in series; the voltmeter’s resistance is 1,950 + 50 = 2,000 Ω.

d.

A galvanometer of resistance 40 Ω gives full-scale deflection for 2 mA. A shunt of 0.04 Ω is connected across it. What is the largest current the ammeter can now read?

Hint

Find the p.d. across the coil at full scale; the shunt has the same p.d. across it. The total current is the coil’s plus the shunt’s.

Answer

At full scale the p.d. across the coil is IgG=0.002×40=0.08 V I_gG = 0.002 \times 40 = 0.08\ \text{V} . The same p.d. is across the shunt, so the shunt carries 0.080.04=2 A \frac{0.08}{0.04} = 2\ \text{A} .
I=Ig+IS=0.002+2=2.002 A I = I_g + I_S = 0.002 + 2 = 2.002\ \text{A}
About 2 A.

e.

A galvanometer of resistance 20 Ω gives full-scale deflection for 5 mA. A resistance of 980 Ω is connected in series with it. What is the range of the voltmeter made?

Hint

The voltmeter’s full-scale voltage drives Ig I_g through G+R G + R .

Answer

V=Ig(G+R)=0.005×(20+980)=0.005×1,000=5 V V = I_g(G + R) = 0.005 \times (20 + 980) = 0.005 \times 1{,}000 = 5\ \text{V}
0 to 5 V.

f.

A galvanometer giving full-scale deflection for 25 mA needs a shunt of 0.25 Ω to read up to 5 A. Find the resistance of the galvanometer.

Hint

Start from IgG=(I−Ig)S I_gG = (I - I_g)S and solve it for G G .

Answer

From IgG=(I−Ig)S I_gG = (I - I_g)S :
G=(I−Ig)SIg=(5−0.025)×0.250.025=4.975×0.250.025=49.75 Ω G = \frac{(I - I_g)S}{I_g} = \frac{(5 - 0.025) \times 0.25}{0.025} = \frac{4.975 \times 0.25}{0.025} = 49.75\ \Omega
About 49.75 Ω (about 50 Ω).

g.

A car battery has six lead-acid cells in series, each of 2.1 V when fully charged. Its capacity is 60 Ah. (i) What is its voltage? (ii) For about how long could it keep two headlights lit, if together they take 9 A?

Hint

Six cells in series add their voltages. Capacity (Ah) ÷ current (A) gives the hours.

Answer
  • i.6 × 2.1 = 12.6 V.
  • ii.t=60 Ah9 A=6.7 hours t = \frac{60\ \text{Ah}}{9\ \text{A}} = 6.7\ \text{hours} : about 6⅔ hours in the ideal case. (A battery drained flat that way would be badly damaged, and might not start the car.)
h.

A shop in Bhaktapur keeps four 10 W LED lights and a 60 W fan running during power cuts, on an inverter with a 12 V battery. The longest power cut is 3 hours. Ignoring losses in the inverter, find (i) the energy needed, in watt-hours, (ii) the charge needed, in ampere-hours, and (iii) the smallest battery capacity if no more than half of its charge is to be used.

Hint

Energy (Wh) = power (W) × time (h). Charge (Ah) = energy (Wh) ÷ voltage (V).

Answer
  • i.Power: 4 × 10 + 60 = 100 W. Energy: 100 W × 3 h = 300 Wh.
  • ii.Charge: 300 Wh12 V= \frac{300\ \text{Wh}}{12\ \text{V}} = 25 Ah (the current is 100 ÷ 12 ≈ 8.3 A for 3 hours).
  • iii.If only half may be used, the battery must hold twice that: 50 Ah at least. (Shops would choose a larger one, since the inverter loses some energy and old batteries hold less.)
i.

A silicon diode and a 1 kΩ resistor are joined in series to a 9 V battery. Find the current when the diode is forward biased. What is the current, and the p.d. across the diode, when it is reversed?

Hint

A forward-biased silicon diode takes about 0.7 V; the resistor takes the rest. Reversed, no current flows.

Answer

Forward: I=9−0.71,000=0.0083 A= I = \frac{9 - 0.7}{1{,}000} = 0.0083\ \text{A} = 8.3 mA.
Reversed: practically no current, so there is no p.d. across the resistor, and the whole 9 V is across the diode.

j.

A red LED works with 2 V across it and a current of 20 mA. What resistance must be put in series with it to run it from a 5 V phone charger?

Hint

The resistor must take the voltage the LED doesn’t: 5 − 2 = 3 V, at the LED’s current.

Answer

The resistor must take the rest of the voltage: 5 − 2 = 3 V, at 20 mA = 0.02 A.
R=30.02=150 Ω R = \frac{3}{0.02} = 150\ \Omega
150 Ω in series. Without it, the LED would take far too much current and burn out.

k.

In a transistor, the collector current is 100 times the base current. (i) What collector current flows for a base current of 0.04 mA? (ii) What base current is needed to switch on a lamp that takes 0.15 A?

Hint

Collector current = 100 × base current. Change 0.15 A into mA for (ii).

Answer
  • i.IC=100×0.04 mA= I_C = 100 \times 0.04\ \text{mA} = 4 mA.
  • ii.IB=150 mA100= I_B = \frac{150\ \text{mA}}{100} = 1.5 mA.